Overview
The G2 Axle and Gear 4-XJ6-456M is a 4.56 ring and pinion gear set with front and rear minor installation kits for the 2000–2001 Jeep Cherokee XJ. The kit pairs a 4.56 front gear set for the Dana 30 short front axle with a 4.56 rear gear set for the Chrysler 8.25-inch rear axle, so both axles of the Jeep are regeared in one kit.
For the 4-XJ6-456M, G2 describes its complete ring and pinion kits as including everything needed for a gear swap: front and rear gear sets plus the minor installation kits for both axles. The 4-XJ6-456M gives Cherokee XJ owners a 4.56 option for changing axle gearing, and G2 says its gears are engineered for oversized tires and high performance engines.
Key features
- Complete front and rear set: 4.56 ring and pinion gear sets for both axles plus matched minor installation kits
- Built for the Dana 30 short front axle and the Chrysler 8.25-inch rear axle
- Computer heat treated 8620 steel gears
- Manufactured to O.E. specifications.
- Double shot peened and double lapped gear sets
- Limited lifetime warranty listed by G2
- Front carrier note: 3.73 and up carrier
Break-in and gear setup
Changing ring and pinion ratios is precision work. Gear mesh and bearing preload set the life of the new gears, so the carriers should be set up with the correct shims and checked against the gear pattern before the axle goes back together. Experienced installers often use a dial indicator and marking compound to confirm contact.
After installation, drive gently for the first stretch so the new gears can seat. Avoid hard launches, heavy towing and long high-speed runs until the lubricant has been changed. Check the gear oil level and look for leaks at the carrier and axle seals, then recheck after the first few drives. If you run larger tires later, the gear ratio will change how the drivetrain behaves at low speed.
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 4-XJ6-456M |
| UPC | 631410141481 |
| Product type | Ring and pinion gear sets with front and rear minor installation kits |
| Gear ratio | 4.56 |
| Vehicle named in listing | 2000–2001 Jeep Cherokee XJ |
| Front axle | Dana 30 short (3.73 and up carrier) |
| Rear axle | Chrysler 8.25-inch |
| Axle location | Front and rear |
| Kit type | Minor kit |
| Gear material | Computer heat treated 8620 steel |
| Finishing | Double shot peened, double lapped |
| Manufacturing | Manufactured to O.E. specs |
| Warranty | Limited lifetime warranty |
Vehicle fitment
The kit fits the 2000–2001 Jeep Cherokee XJ. It has a Dana 30 short front axle (3.73 and up carrier) and a Chrysler 8.25-inch rear axle, so it applies to a Jeep with those axles. It does not cover other Cherokee XJ model years, the SJ and KL Cherokee, or the Grand Cherokee. Check fit against your vehicle’s year, model and trim before ordering.
The 4-XJ6-456M listing does not cover Cherokee XJ model years outside 2000–2001, other Cherokee generations such as the SJ and KL, and the Grand Cherokee. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Fitting the 4-XJ6-456M changes the gear ratio on both axles of a Cherokee XJ, which is work for an experienced gear installer. The two minor installation kits in the 4-XJ6-456M are the parts used for setting the new gears, and the same 4.56 ratio goes in both axles so the drivetrain stays matched. The 4-XJ6-456M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-XJ6-456M gears after installation.
What’s included
- Front ring and pinion gear set, 4.56
- Rear ring and pinion gear set, 4.56
- Front minor installation kit
- Rear minor installation kit







