Overview
The G2 Axle and Gear 35-2046 is a master ring and pinion installation kit for the Ford 10.25 Inches rear axle.
The 35-2046 is the master kit for gear installs in the Ford 10.25 inch rear axle. It bundles Timken pinion and carrier bearings with races, shim sets, a crush sleeve, nut, seal, ring gear bolts, and sealing and marking compounds. It also lets 10.25 inch gears run in a 10.5 inch housing.
G2’s 35-2046 has two jobs. It is the master kit for 1986-1997 Ford Sterling rear axles, and it also lets 10.25 inch gears be installed in a 10.5 inch axle housing. In both cases the gears must be Ford 10.25 inch gears, and the kit adds Timken bearings and races, shims, a crush sleeve, a pinion seal and nut, bolts, and the sealing and marking compounds.
Key features
- Master installation kit for the Ford 10.25 Inches axle (rear)
- Includes pinion Nut
- Includes pinion Seal
- Includes Timken Outer Pinion Bearing and Race
- Includes crush Sleeve
- Includes Timken Inner Pinion Bearing and Race
- Includes pinion Shims
- Includes carrier Shims
- Includes carrier Bearings and Races
- Includes ring Gear Bolts
Pinion setup with a master kit
A master kit covers the parts that get replaced during a pinion and carrier rebuild, which makes the job more predictable. The 10.25 inch axle needs correct pinion depth, bearing preload and backlash, and those settings depend on the shims and the crush sleeve working together.
Gear pattern checks are the final step. Coat the ring gear with marking compound, turn the pinion, and read the contact area before the cover goes on. If the pattern is off, adjust pinion shims first, then carrier shims to restore backlash.
Keep bearing races seated fully and clean the housing surfaces before sealing. Old ring gear bolts should not be reused, and the threads should be cleaned before the thread locker is applied. Work in a clean area.
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 35-2046 |
| UPC | 631410095951 |
| Kit type | Master kit with bearings |
| Axle location | Rear |
| Axle type | Ford 10.25 Inches |
| Axle manufacturer | Ford |
Vehicle fitment
The kit is for 1986-1997 Ford Sterling rear axles and must be used with Ford 10.25 inch gears only. It also allows 10.25 inch gears to be installed in a 10.5 inch axle housing, so confirm the gear size before using it.
Confirm your vehicle’s axle type, spline count and year before ordering.
Installation notes
Because the kit is tied to 10.25 inch gears, check the ring gear diameter and tooth count before dismantling. Then set pinion depth with the shims, tighten the pinion to the crush sleeve, and verify the pattern.
Before opening the Ford 10.25 Inches housing for the 35-2046 job, gather a dial indicator, a torque wrench and clean gear oil. Record the original gear pattern, because the 35-2046 shims are the tool for moving the new pattern toward it. Fit the new nut and seal. Sort shims by thickness.
What’s included
- Pinion Nut
- Pinion Seal
- Timken Outer Pinion Bearing and Race
- Crush Sleeve
- Timken Inner Pinion Bearing and Race
- Pinion Shims
- Carrier Shims
- Carrier Bearings and Races
- Ring Gear Bolts
- Thread Locking Compound
- Gear Marking Compound
- Silicone Sealer
Not included: ring and pinion gears; the 35-2046 supplies installation parts for the Ford 10.25 Inches axle only.













