Overview
The G2 Axle and Gear 35-2049 is a master ring and pinion installation kit for the Dana 35 rear axle.
The 35-2049 is G2’s general-purpose master kit for the Dana 35. It bundles Timken inner and outer pinion bearings, carrier bearings with races, both shim sets, a crush sleeve, a pinion seal and nut, new ring gear bolts, and sealer and compounds for the final assembly. That covers the whole parts list for a gear swap on the supported axles.
Where the 35-2049 fits in G2’s Dana 35 range: it is the version without a special carrier, so it suits the common rear axle and the standard rotation IFS front unit. The Timken bearings and races, both shim families and the new bolts let the installer replace everything that wears at the gear mesh. The silicone sealer closes the cover, and the thread locker secures the ring gear bolts.
Key features
- Master installation kit for the Dana 35 axle (rear)
- Includes pinion Nut
- Includes pinion Seal
- Includes Timken Outer Pinion Bearing and Race
- Includes crush Sleeve
- Includes Timken Inner Pinion Bearing and Race
- Includes pinion Shims
- Includes carrier Shims
- Includes carrier Bearings and Races
- Includes ring Gear Bolts
Dana 35 setup in practice
Pinion depth and carrier preload define how a Dana 35 gear set performs. Those settings need a dial indicator, a torque wrench and patience, since small shim changes move the tooth contact noticeably. Set the pinion first, then the carrier, and recheck the pattern after each change.
Axle shaft spline count matters when choosing a kit. A rear axle that has been converted to a different spline count may need different axle shafts or a different master kit. Confirm the axle’s identity from its housing and shaft markings before ordering, and keep the original parts for reference.
Gear wear shows up in the contact pattern, in noise under load, and in metal in the oil. Replacing the pinion bearings and carrier bearings with the gears keeps the set aligned. Break in new gears gently with light loads for the first stretch of driving.
- Record the original gear pattern
- Sort shims by thickness before fitting
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 35-2049 |
| UPC | 631410095982 |
| Kit type | Master kit with bearings |
| Axle location | Rear |
| Axle type | Dana 35 |
| Axle manufacturer | Dana |
Vehicle fitment
It fits Dana 35 rear axles and Dana 35 IFS front axles with standard rotation. Rear axles converted with the 30 spline axle upgrade kit are excluded and need kit 35-2049L. Confirm your vehicle’s axle type, spline count and year before ordering.
Confirm your vehicle’s axle type, spline count and year before ordering.
Installation notes
Gear setup on a Dana 35 means measuring pinion depth, adjusting carrier preload and checking the pattern with marking compound, which is why a trained installer is the usual choice. Run new gears gently for the first miles.
Before opening the Dana 35 housing for the 35-2049 job, gather a dial indicator, a torque wrench and clean gear oil. Record the original gear pattern, because the 35-2049 shims are the tool for moving the new pattern toward it. Fit the new nut and seal. Sort shims by thickness.
What’s included
- Pinion Nut
- Pinion Seal
- Timken Outer Pinion Bearing and Race
- Crush Sleeve
- Timken Inner Pinion Bearing and Race
- Pinion Shims
- Carrier Shims
- Carrier Bearings and Races
- Ring Gear Bolts
- Thread Locking Compound
- Gear Marking Compound
- Silicone Sealer
Not included: ring and pinion gears; the 35-2049 supplies installation parts for the Dana 35 axle only.





















