Overview
The G2 Axle and Gear 35-2011C is a master ring and pinion installation kit with bearings for the Ford 9-inch, 3.25-inch bore axle, for the rear axle position.
The 35-2011C includes the parts needed to install a ring and pinion, with pinion, pilot and carrier bearings along with the shims, nut, seal and compounds. Some of its parts are hard-to-find items that auto parts stores rarely stock. It is made for aftermarket 3.25-inch bore cases, Daytona style pinion supports and aftermarket 35 spline carriers. The ring and pinion gear set is not included.
Key features
- Master kit with bearings for the Ford 9-inch, 3.25-inch bore axle
- Timken outer and inner pinion bearings and races
- Timken pinion pilot bearing included
- Carrier bearings and races included
- Pinion nut, crush sleeve, pinion seal and ring gear bolts
- Thread locking compound, gear marking compound and silicone sealer
- For use with aftermarket 3.25-inch bore case
- For use with Daytona style pinion support
- For use with aftermarket 35 spline carriers
Matching the case and pinion support
This kit is built around a specific case and pinion support arrangement. Before buying, confirm the housing is an aftermarket 3.25-inch bore case and that the pinion support is the Daytona style. Mixing a different pinion support with this gear set can change pinion depth and make the setup difficult to correct.
The 35 spline carrier is the other half of the match. Check the carrier splines and bearing bores against the gear set before assembly, and make sure the pilot bearing seats squarely in the pinion support. Once the parts are verified, the rebuild goes more smoothly and gear marking is easier to read.
- Verify the case bore before ordering
- Check pinion support style against the carrier
- Inspect spline wear on the carrier and axle shafts
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 35-2011C |
| UPC | 631410095548 |
| Product type | Master ring and pinion installation kit with bearings |
| Axle | Ford 9-inch, 3.25-inch bore |
| Axle location | Rear |
| Popular axle manufacturer | Ford |
| Kit type | Master kit with bearings |
| Listing condition | For use with aftermarket 3.25-inch bore case |
| Listing condition | For use with Daytona style pinion support |
| Listing condition | For use with aftermarket 35 spline carriers |
| Contents | Pinion nut, pinion seal, Timken outer pinion bearing and race, crush sleeve, Timken inner pinion bearing and race, pinion shims, Timken pinion pilot bearing, carrier shims, carrier bearings and races, ring gear bolts, thread locking compound, gear marking compound, silicone sealer |
Vehicle fitment
The 35-2011C is identified by axle rather than by vehicle: it is made for the Ford 9-inch, 3.25-inch bore axle in the rear position. It is for aftermarket 3.25-inch bore cases, Daytona style pinion supports and aftermarket 35 spline carriers. Confirm fit for your vehicle’s year, model and trim before ordering.
Other axle designs and sizes fall outside this kit. Confirm fit for your vehicle’s year, model and trim before ordering.
Installation notes
A master kit such as the 35-2011C rebuilds the gear setup completely, so the bearings are replaced along with the gear set. The pinion shims, carrier shims, crush sleeve and gear marking compound in the 35-2011C are the parts used to set pinion depth, preload and the tooth contact pattern, which calls for an installer with gear setup experience and a careful break-in afterwards.
What’s included
- Pinion nut
- Pinion seal
- Timken outer pinion bearing and race
- Crush sleeve
- Timken inner pinion bearing and race
- Pinion shims
- Timken pinion pilot bearing
- Carrier shims
- Carrier bearings and races
- Ring gear bolts
- Thread locking compound
- Gear marking compound
- Silicone sealer
Not included with the 35-2011C: ring and pinion gear set.











