Select your vehicle

G2 Dana 30/35 YJ 4.10 Ring and Pinion Minor Installation Kit – 4-YJ-410M

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits the 1987–1995 Jeep Wrangler YJ (87-95 Wrangler YJ).
  • 4.10 ring and pinion gear sets, front and rear
  • Dana 30 front and Dana 35 rear axles
  • Includes matched front and rear minor installation kits
  • Limited lifetime warranty

Description

Overview

The G2 Axle and Gear 4-YJ-410M is a 4.10 ring and pinion gear set with front and rear minor installation kits for the 1987–1995 Jeep Wrangler YJ. The kit pairs a 4.10 front gear set for the Dana 30 front axle with a 4.10 rear gear set for the Dana 35 rear axle, so both axles of the Jeep are regeared in one kit.

For the 4-YJ-410M, G2 describes its complete ring and pinion kits as including everything needed for a gear swap: front and rear gear sets plus the minor installation kits for both axles. The 4-YJ-410M gives Wrangler YJ owners a 4.10 option for changing axle gearing, and G2 says its gears are engineered for oversized tires and high performance engines.

Key features

  • Complete front and rear set: 4.10 ring and pinion gear sets for both axles plus matched minor installation kits
  • Built for the Dana 30 front axle and the Dana 35 rear axle
  • Computer heat treated 8620 steel gears
  • Made to O.E. spec standards.
  • Double shot peened and double lapped gear sets
  • Limited lifetime warranty listed by G2

Keeping the new gears healthy

The Dana 30 front and Dana 35 rear are different axles with different housings, so each side is set up separately even though the ratio matches. Front axles on a YJ work through steering and tire clearance, while the rear carries the main driveline load. Both sides benefit from the same careful setup and break-in.

Gear life depends on fresh lubrication, steady loads during break-in, and a clean housing. Inspect the axle seals and vent after installation, and listen for changes in noise over the first weeks. Early warning signs include metallic debris in the fluid and a whine that changes with speed.

  • Change fluid after break-in
  • Check axle seals at each oil change
  • Watch for metal shavings in the drain plug

Specifications

Brand G2 Axle and Gear
Part number 4-YJ-410M
UPC 631410141269
Product type Ring and pinion gear sets with front and rear minor installation kits
Gear ratio 4.10
Vehicle named in listing 1987–1995 Jeep Wrangler YJ
Front axle Dana 30
Rear axle Dana 35
Axle location Front and rear
Kit type Minor kit
Gear material Computer heat treated 8620 steel
Finishing Double shot peened, double lapped
Manufacturing Manufactured to O.E. specs
Warranty Limited lifetime warranty

Vehicle fitment

It fits the 1987–1995 Jeep Wrangler YJ (87-95 Wrangler YJ). It uses a Dana 30 front axle and a Dana 35 rear axle, so it applies to a Jeep with those axles.

The 4-YJ-410M listing does not cover the Wrangler TJ (1997–2006), the Wrangler JK (2007–2018) and other Jeep models. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Fitting the 4-YJ-410M changes the gear ratio on both axles of a Wrangler YJ, which is work for an experienced gear installer. The two minor installation kits in the 4-YJ-410M are the parts used for setting the new gears, and the same 4.10 ratio goes in both axles so the drivetrain stays matched. The 4-YJ-410M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-YJ-410M gears after installation.

What’s included

  • Front ring and pinion gear set, 4.10
  • Rear ring and pinion gear set, 4.10
  • Front minor installation kit
  • Rear minor installation kit
SKU: G/24-YJ-410M Category:

Specification

Shipping weight 28.00 lbs
Package dimensions 0.00 × 0.00 × 0.00 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (YJ) likely fits1987–1995All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Which vehicles does the G2 4-YJ-410M fit?

The G2 4-YJ-410M is made for the 1987–1995 Jeep Wrangler YJ. Confirm your Jeep's axles match the Dana 30 front and Dana 35 rear before choosing it.

What gear ratio is the G2 4-YJ-410M?

The 4-YJ-410M is a 4.10 ratio kit. Both ring and pinion sets in the 4-YJ-410M, front and rear, are 4.10, so the two axles stay matched after the gear swap.

Does the 4-YJ-410M include both front and rear gears?

Yes. The 4-YJ-410M includes front and rear gear sets plus matched minor installation kits for both axles, so both axles are regeared together.

Which axles is the 4-YJ-410M made for?

The 4-YJ-410M is made for a Dana 30 front axle and a Dana 35 rear axle on the Wrangler YJ. The 4-YJ-410M is not a kit for other axle combinations, so check your Jeep's axles first.

What materials and finishing are used on the 4-YJ-410M gears?

The gears use computer heat treated 8620 steel with double shot peening and double lapping. They are manufactured to O.E. specifications, and a limited lifetime warranty is included.

Is it safe to drive the YJ right after the gear swap?

Drive gently until the break-in is complete. Keep loads and speeds moderate, check for heat, noise and leaks during early drives, and have a shop confirm mesh and backlash if anything changes.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon