Select your vehicle

G2 Dana 30/35 XJ 4.88 Ring and Pinion Minor Installation Kit – 4-XJ2-488M

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits the 1990–1996 Jeep Cherokee XJ
  • 4.88 ring and pinion gear sets, front and rear
  • Dana 30 reverse front and Dana 35 rear axles
  • Includes matched front and rear minor installation kits
  • Limited lifetime warranty

Description

Overview

The G2 Axle and Gear 4-XJ2-488M is a 4.88 ring and pinion gear set with front and rear minor installation kits for the 1990–1996 Jeep Cherokee XJ. The kit pairs a 4.88 front gear set for the Dana 30 reverse front axle with a 4.88 rear gear set for the Dana 35 rear axle, so both axles of the Jeep are regeared in one kit.

For the 4-XJ2-488M, G2 describes its complete ring and pinion kits as including everything needed for a gear swap: front and rear gear sets plus the minor installation kits for both axles. The 4-XJ2-488M gives Cherokee XJ owners a 4.88 option for changing axle gearing, and G2 says its gears are engineered for oversized tires and high performance engines.

Key features

  • Complete front and rear set: 4.88 ring and pinion gear sets for both axles plus matched minor installation kits
  • Built for the Dana 30 reverse front axle and the Dana 35 rear axle
  • Computer heat treated 8620 steel gears
  • Manufactured to O.E. specifications.
  • Double shot peened and double lapped gear sets
  • Limited lifetime warranty listed by G2
  • Carrier requirements: front 3.73 and up carrier, rear 3.54 and up carrier.

Carrier fit and axle matching

The carrier rating is a key part of a gear swap, because the ring gear must match the carrier it bolts into. A carrier that is not rated for the new set will not seat properly and may not hold the correct backlash. Confirm the carrier type and rating on both axles before any gears are pulled, and keep the old carrier and gear markings for reference.

On an XJ, the front and rear axles often wear differently depending on how the vehicle has been used. Inspect the pinion bearings, the axle seals and the differential case for wear while the axles are open. Replacing those parts during the swap reduces the chance of returning to the shop soon after a regear.

  • Verify carrier rating on each axle
  • Inspect pinion bearings and seals while open
  • Keep old gear markings for reference

Specifications

Brand G2 Axle and Gear
Part number 4-XJ2-488M
UPC 631410141375
Product type Ring and pinion gear sets with front and rear minor installation kits
Gear ratio 4.88
Vehicle named in listing 1990–1996 Jeep Cherokee XJ
Front axle Dana 30 reverse (3.73 and up carrier)
Rear axle Dana 35 (3.54 and up carrier)
Axle location Front and rear
Kit type Minor kit
Gear material Computer heat treated 8620 steel
Finishing Double shot peened, double lapped
Manufacturing Manufactured to O.E. specs
Warranty Limited lifetime warranty

Vehicle fitment

It fits the 1990–1996 Jeep Cherokee XJ, and it applies to a Jeep with a Dana 30 reverse front axle and a Dana 35 rear axle. It does not fit Cherokee XJ years outside 1990–1996, other Cherokee generations such as the SJ and KL, or the Grand Cherokee. Confirm fit for your vehicle’s year, model and trim before ordering.

The 4-XJ2-488M listing does not cover Cherokee XJ model years outside 1990–1996, other Cherokee generations such as the SJ and KL, and the Grand Cherokee. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Fitting the 4-XJ2-488M changes the gear ratio on both axles of a Cherokee XJ, which is work for an experienced gear installer. The two minor installation kits in the 4-XJ2-488M are the parts used for setting the new gears, and the same 4.88 ratio goes in both axles so the drivetrain stays matched. The 4-XJ2-488M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-XJ2-488M gears after installation.

What’s included

  • Front ring and pinion gear set, 4.88
  • Rear ring and pinion gear set, 4.88
  • Front minor installation kit
  • Rear minor installation kit
SKU: G/24-XJ2-488M Category:

Specification

Shipping weight 29.00 lbs
Package dimensions 0.00 × 0.00 × 0.00 in
brands

Fitment

VehicleYearsTrims
Jeep Cherokee (XJ) likely fits1990–1996All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Which vehicles does the G2 4-XJ2-488M fit?

The G2 4-XJ2-488M fits the 1990–1996 Jeep Cherokee XJ. Confirm your Jeep's axles match the Dana 30 reverse front and Dana 35 rear before choosing it.

What gear ratio is the G2 4-XJ2-488M?

The 4-XJ2-488M is a 4.88 ratio kit. Both ring and pinion sets in the 4-XJ2-488M, front and rear, are 4.88, so the two axles stay matched after the gear swap.

Does the 4-XJ2-488M include both front and rear gears?

Yes. It includes front and rear gear sets plus matched minor installation kits for both axles, making it a complete gear swap package.

Which axles is the 4-XJ2-488M made for?

The 4-XJ2-488M is made for a Dana 30 reverse (3.73 and up carrier) front axle and a Dana 35 (3.54 and up carrier) rear axle on the Cherokee XJ. The 4-XJ2-488M is not a kit for other axle combinations, so check your Jeep's axles first.

What materials and finishing are used on the 4-XJ2-488M gears?

The gears are made from computer heat treated 8620 steel, with double shot peening and double lapping, and are manufactured to O.E. specifications. The kit carries a limited lifetime warranty.

How can I tell if the carrier is suitable for a new ring gear?

Check the carrier rating and the axle codes stamped on the housing and carrier against the gear set before ordering. A carrier that does not match will not hold the ring gear square, so confirm it before any parts are removed.

Should the gear oil be changed after a regear?

Yes. Fresh gear oil after the break-in period removes metal particles from the new teeth and keeps the bearings and gears protected. Use the lubricant type recommended for the axle.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon