Select your vehicle

G2 Dana 30/35 XJ 4.10 Ring and Pinion Minor Installation Kit – 4-XJ2-410M

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits the 1990–1996 Jeep Cherokee XJ
  • 4.10 ring and pinion gear sets, front and rear
  • Dana 30 reverse front and Dana 35 rear axles
  • Includes matched front and rear minor installation kits
  • Limited lifetime warranty

Description

Overview

The G2 Axle and Gear 4-XJ2-410M is a 4.10 ring and pinion gear set with front and rear minor installation kits for the 1990–1996 Jeep Cherokee XJ. The kit pairs a 4.10 front gear set for the Dana 30 reverse front axle with a 4.10 rear gear set for the Dana 35 rear axle, so both axles of the Jeep are regeared in one kit.

For the 4-XJ2-410M, G2 describes its complete ring and pinion kits as including everything needed for a gear swap: front and rear gear sets plus the minor installation kits for both axles. The 4-XJ2-410M gives Cherokee XJ owners a 4.10 option for changing axle gearing, and G2 says its gears are engineered for oversized tires and high performance engines.

Key features

  • Complete front and rear set: 4.10 ring and pinion gear sets for both axles plus matched minor installation kits
  • Built for the Dana 30 reverse front axle and the Dana 35 rear axle
  • Computer heat treated 8620 steel gears
  • Manufactured to O.E. specifications.
  • Double shot peened and double lapped gear sets
  • Limited lifetime warranty listed by G2
  • Carrier fit: front 3.73 and up carrier; rear 3.54 and up carrier

Axle gearing and daily use

Moving to a 4.10 ratio raises engine speed at a given road speed, which helps acceleration and low-speed pulling. The trade-off is more engine revolutions on the highway and possibly higher fuel use, depending on how the truck is driven and what tires it wears. Gearing is a balance of tire size, engine power and typical loads.

A regear is a good moment to inspect what sits behind the gears. Pinion and carrier bearings, axle seals and fluid are commonly renewed during the work, and inspecting shafts and axle ends can save a second teardown. Speedometer calibration may also need adjusting once the ratio changes, so note any reading differences.

  • Weigh highway speed against low-speed pull
  • Replace axle fluid with the new gears
  • Check shafts and seals while the axle is open
  • Note speedometer changes after installation

Specifications

Brand G2 Axle and Gear
Part number 4-XJ2-410M
UPC 631410141351
Product type Ring and pinion gear sets with front and rear minor installation kits
Gear ratio 4.10
Vehicle named in listing 1990–1996 Jeep Cherokee XJ
Front axle Dana 30 reverse (3.73 and up carrier)
Rear axle Dana 35 (3.54 and up carrier); this axle is marked 4.11
Axle location Front and rear
Kit type Minor kit
Gear material Computer heat treated 8620 steel
Finishing Double shot peened, double lapped
Manufacturing Manufactured to O.E. specs
Warranty Limited lifetime warranty

Vehicle fitment

It fits the 1990–1996 Jeep Cherokee XJ (90-96 XJ Cherokee), with a Dana 30 reverse front axle and a Dana 35 rear axle, so it applies to a Jeep with those axles.

The 4-XJ2-410M listing does not cover Cherokee XJ model years outside 1990–1996, other Cherokee generations such as the SJ and KL, and the Grand Cherokee. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Fitting the 4-XJ2-410M changes the gear ratio on both axles of a Cherokee XJ, which is work for an experienced gear installer. The two minor installation kits in the 4-XJ2-410M are the parts used for setting the new gears, and the same 4.10 ratio goes in both axles so the drivetrain stays matched. The 4-XJ2-410M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-XJ2-410M gears after installation.

What’s included

  • Front ring and pinion gear set, 4.10
  • Rear ring and pinion gear set, 4.10
  • Front minor installation kit
  • Rear minor installation kit
SKU: G/24-XJ2-410M Category:

Specification

Shipping weight 28.00 lbs
Package dimensions 0.00 × 0.00 × 0.00 in
brands

Fitment

VehicleYearsTrims
Jeep Cherokee (XJ) likely fits1990–1996All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Which vehicles does the G2 4-XJ2-410M fit?

It is made for the 1990–1996 Jeep Cherokee XJ. Before choosing the 4-XJ2-410M, confirm the Dana 30 reverse front and Dana 35 rear axles match your Jeep.

What gear ratio is the G2 4-XJ2-410M?

It is a 4.10 ratio kit, with front and rear ring and pinion sets both at 4.10. Matching ratios keep the two axles working together after the swap.

Does the 4-XJ2-410M include both front and rear gears?

Yes. Front and rear gear sets come with matched minor installation kits for both axles, so one package covers the full regear.

Which axles is the 4-XJ2-410M made for?

It is made for a Dana 30 reverse front axle and a Dana 35 rear axle, with 3.73 and up and 3.54 and up carriers, on the Cherokee XJ. Other axle combinations fall outside it, so verify your axles first.

What materials and finishing are used on the 4-XJ2-410M gears?

Computer heat treated 8620 steel is used for the gears, which are double shot peened, double lapped and manufactured to O.E. specifications. A limited lifetime warranty applies.

Can the gears be replaced without new bearings?

Sometimes, but worn bearings are a common cause of noise after a regear. Inspect them for pitting, play and heat discoloration, and replace any that show wear so the new gears set up correctly.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon