Overview
The Baer Brakes Tracker 3301010 is an adjustable front tie rod kit for 1988–1998 GM C10 2WD trucks and 1992–1999 GM C10 2WD SUVs that use stock spindles. The adjustable sleeve helps correct bump steer, which can come from modified suspensions or factory design.
The tie rods use a 6061 T-6 aluminum sleeve with a black e-coated finish, a Teflon lined 5/8 inch heim joint and a 4140 steel pin. The pin is tapered and heat treated after machining, so it fits stock spindles without modification. The set provides 0.875 inch of adjustment at the spindle.
Key features
- Direct bolt-on upgrade for stock C10 spindles
- Tapered 4140 steel pin that fits stock spindles without modification
- 0.875 inch of adjustment at the spindle
- 6061 T-6 aluminum sleeve with black e-coated finish
- Teflon lined 5/8 inch heim joints
- Pre-greased and greaseable joints
- Reinforced tube with locking nut and washers
Steering geometry basics
Tie rods link the steering box or rack to the steering knuckles, so their length sets toe and affects how the truck tracks on the road. Bump steer happens when the steering arm and suspension move through different arcs, causing the front wheels to steer on their own over bumps. Adjustable sleeves let you tune the geometry, but any change should be followed by an alignment check.
Worn steering parts often show up as loose steering, wandering or uneven front tire wear. Check tie rod ends, ball joints and the drag link with the truck raised, looking for play and torn dust boots. Keep grease fittings and boots in good condition, since grit and water shorten joint life on a truck that sees rough use.
- Set sleeve length before the final alignment
- Replace torn boots before grit gets into the joint
- Check the drag link and ball joints together with the tie rods
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 3301010 |
| UPC | 844165004998 |
| Sold as | Kit |
| Includes | Two tie rods |
| Axle | Front |
| Steering type | Manual |
| Type | Straight |
| Sleeve material | 6061 T-6 aluminum |
| Finish | Black e-coated |
| Sleeve length | 8.125 inch |
| Adjustment range | 0.875 inch |
| Inner sleeve thread | 11/16 inch x 18 left hand |
| Outer sleeve thread | 5/8 inch x 18 right hand |
| Tube diameter | 5/8 inch |
| Heim joint | Teflon lined 5/8 inch |
| Pin material | 4140 steel |
| End 1 and end 2 gender | Female |
| Pre-greased | Yes |
| Greaseable | Yes |
| Locking nut included | Yes |
| Washers included | Yes |
| Mounting hardware included | Yes |
| Castle nut included | No |
| Cotter pin included | No |
| Dust boot included | No |
| Grease fitting included | No |
| Country of origin | US |
Vehicle fitment
It fits 1988–1998 Chevrolet C1500 and GMC C1500 trucks, 1992–1999 Chevrolet C1500 Suburban and GMC C1500 Suburban models, and 1995–1999 Chevrolet Suburban 1500 and Tahoe models. Covered trims include Silverado, Scottsdale, Cheyenne, Sierra and several LS, LT and SLE options depending on the model.
It is for 2WD applications only, so 4WD versions do not fit. Confirm fit for your vehicle’s year, model and trim before ordering.
Installation notes
The tapered pin is designed to use the stock spindles, so Baer describes no spindle modification. Set the sleeve length and then have toe checked after installation, since tie rod length changes alignment. Tie rods are steering components, so have the installation inspected by a qualified technician.
What’s included
Two adjustable tie rods with adjusting sleeves, a locking nut, mounting hardware and washers.
Not included: castle nut, cotter pin, dust boot and grease fitting.













