Overview
The Alloy USA 17140 is a GM 14 bolt 9.5 inch rear axle shaft with 33 splines, for the driver or passenger side. It fits 81-91 GM 2500LD models and a range of Chevrolet and GMC Suburbans.
In Alloy USA’s words, an axle shaft should be upgraded and not just replaced. It says its shafts, in 1541H or 4140 steel, are heat treated and induction hardened to be up to 35% stronger than stock. Spline count matters: the 33 splines on the 17140 have to agree with the gear set inside the axle.
Key features
- Replacement shaft for the GM 14 bolt 9.5 inch rear axle
- 33 spline
- Fits the driver or passenger side
- Covers 81-91 GM 2500LD trucks.
- Alloy USA says its shafts are heat treated and induction hardened
- Bearings, seals and studs are not included
Suburban and 2500LD axle use
The 14 bolt 9.5 inch rear axle is used under heavy trucks and Suburbans, where the shafts carry steady torque and loads from towing. Because the spline count must match the gear set inside the housing, the shaft is a fit-sensitive part. Check the old shaft for twisted splines, cracks and bearing wear before deciding whether a shaft or a full axle rebuild is needed.
Suburbans and larger trucks often carry extra weight, so the shaft and its bearings are under more stress than on a light-duty truck. Check the axle housing seal and the wheel hub for grease leaks or looseness. Installing the shaft with clean splines and fresh bearings helps the new part last. Plan the job so the new shaft, bearings and seals are on hand before work starts.
- Match the spline count to the gear set
- Inspect the housing seal for leaks
- Replace bearings and seals with the shaft
- Check the hub for looseness before reassembly
Specifications
The 17140 is a replacement axle shaft for the GM 14 bolt 9.5 inch rear axle, with 33 splines. Every figure in the table below is the manufacturer value for the 17140.
| Brand | Alloy USA |
|---|---|
| Part number | 17140 |
| Part type | Replacement axle shaft |
| Axle | GM 14 bolt 9.5 inch rear |
| Axle shaft location | Driver or passenger side |
| Spline | 33 spline |
| Manufacturer part number | ALY17140 |
| Application stated | 81-91 GM 2500LD |
Vehicle fitment
The manufacturer fitment list for the 17140 names: 1992–1996 Chevrolet C1500 Suburban; 1981–1986 Chevrolet C20 Suburban; 1992–1996 Chevrolet C2500 Suburban; 1992–1996 Chevrolet K1500 Suburban; 1981–1986 Chevrolet K20 Suburban; 1992–1996 Chevrolet K2500 Suburban; 1987–1988 Chevrolet R20 Suburban; 1989–1991 Chevrolet R2500 Suburban; 1987–1988 Chevrolet V20 Suburban; 1989–1991 Chevrolet V2500 Suburban; 1992–1996 GMC C1500 Suburban; 1981–1986, 1992–1996 GMC C2500 Suburban; 1992–1996 GMC K1500 Suburban; 1994 GMC K2500; 1981–1986, 1992–1996 GMC K2500 Suburban; 1987–1991 GMC R2500 Suburban; 1987–1991 GMC V2500 Suburban.
It is for 81-91 GM 2500LD applications.
Check the old shaft’s spline count and length against the 17140 specifications before you start the job.
Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Bearings, seals and studs are not part of the 17140; they have to be reused or sourced separately.
What’s included
One axle shaft.
Not included: Bearings, Seals, Studs.





