Select your vehicle

Fender Liners under Fenders & Flares covers aluminum inner fenders for the Jeep Wrangler JK and JL and Gladiator JT. Poison Spyder, Fishbone Offroad, DV8 Offroad, Artec Industries, Go Rhino and Addictive Desert Designs make front and rear inner fenders that seal the engine bay or rear wheel wells after tube fenders or high-clearance flares are fitted, several with stainless mesh vents for airflow; Bestop’s Highrock liners and Rough Country complete the set. Compare vented or solid and front or rear below.

Showing 1–12 of 18 resultsSorted by popularity

Why inner fenders matter after a fender swap

The factory plastic fender liners on a Wrangler or Gladiator are shaped to the stock flares. When you install tube fenders, high-clearance flares or cut the stock fenders for 37 inch tires, the old liners no longer fit or come off entirely, leaving the engine bay and the rear tub open to the wheel well. Every rock and mud clod the tire throws then hits the alternator, the battery, the wiring, the fuel filler and the tail lights. Aluminum inner fenders close that gap with flat panels shaped to the new fender opening, bolted to the body and the fender. Most of the products here are for the 2018 to 2026 JL and 2020 to 2022 JT, with the JK covered by Artec and Poison Spyder.

Front or rear, vented or solid

  • Front inner fenders seal the engine compartment from the wheel well. Vented versions, like the Poison Spyder vented front kits for the JL and the JK and the Go Rhino liners with hex mesh vents, let hot air escape the engine bay and are the common choice for a Jeep that idles on slow trails in heat.
  • Solid front liners, like the DV8 Offroad and Fishbone panels, keep more mud and water out and suit mud and water crossings.
  • Rear inner fenders close the opening between the rear flare and the tub so mud does not pack behind the tail lights and the fuel filler. Artec covers the JK two-door and Unlimited; Fishbone and Poison Spyder cover the JL and JT.
  • Coilover-specific kits, like the Poison Spyder JK front liners for aftermarket coilover setups, are cut around the shock towers of a long-travel front end.
  • Big-tire liners, like the Addictive Desert Designs Rock Fighter fronts for 37 inch tires with aftermarket fenders, sit low profile so the tire clears at full stuff.

Material and build

Nearly all of these are aluminum, most in 16 gauge 5052 alloy, which does not rust and weighs less than steel. Makers add stiffness with bead-rolled ribs or a stamped logo, as Poison Spyder and Artec describe, so a thin panel does not drum or flex. Finishes are raw aluminum, which can be left bare or painted, textured black powder coat, or Poison Spyder's gloss black Spydershell coat. Vents use stainless steel wire or hex mesh that resists rust. Bestop's Highrock Granite Series liners are the direct-fit option designed around Bestop's own fenders for the JL and JT.

Fitment considerations

Inner fenders are made to a specific flare or fender. A liner designed for tube fenders will not match the body line of high-clearance plastic flares, and liners made for one maker's fenders may not line up with another's bolt holes. Check the listing for which fenders it is designed to finish. Trim level and year matter on the JL, where some makers list 2018 to 2019 and 2021 to 2022 separately, and the JT shares front liners with the JL in most cases but has its own rear panels. With a long-travel or coilover front end, confirm shock and tire clearance at full compression.

Installation tips

Remove the stock liner remains, test fit each panel with the fender installed, and mark any holes before drilling. Use the supplied stainless hardware with nylon washers so aluminum does not gall against steel. Seal the top edge against the body with foam tape if you want it watertight. Vented panels should be cleared of packed mud after wet trips so the mesh keeps flowing. Confirm the liner matches your exact year, model, door count and fender brand before choosing.

Popular Fender Liners brands

Fender Liners FAQ

Do I need inner fenders if I keep the stock plastic flares?

No. The factory liners fit the stock flares and do the job. Inner fenders are for Jeeps with tube fenders, high-clearance flares or trimmed fenders, where the factory liners no longer fit and the engine bay or rear tub is exposed to the wheel well.

Should I get vented or solid front inner fenders?

Vented panels release engine heat and help on slow, hot trails and rock crawling where the engine idles for hours. Solid panels keep out more mud and spray in wet terrain. Many owners choose vented and clean the mesh after muddy trips.

Will inner fenders for a JL fit a Gladiator JT?

Front inner fenders often fit both, and many listings name the 2018 to 2026 JL and 2020 to 2022 JT together. Rear inner fenders differ because the Gladiator's bed and rear fender shape are different from the Wrangler's tub, so buy rear panels listed specifically for the JT.

Are inner fenders brand-specific to the fenders I have?

Usually. Each maker shapes its panels to its own tube fenders or high-clearance flares, and the bolt locations and edge profile may not match another brand's fenders. Some makers list compatibility with other fender brands; otherwise expect to drill or trim to fit a mixed setup.