Fabrication & Tools
This category is the fabrication shelf for builders: flex joints and Johnny Joint style rod ends, heim joints, jam nuts, tube adapters, gussets, spring perches and shock mounts, plus specialty tools. It serves people building custom links, cages and suspension brackets, or servicing joints. Artec, RockJock, Rubicon Express and Currie are listed often. Check product pages for sizes and part numbers, then compare the products below.

Custom links, weld-on brackets and one-off suspension builds start with the pieces in this section. It is also where you find the odd tools that turn a frustrating axle or shock job into a quick one, like spindle nut sockets, joint presses and coil-over spanners.
Builder parts fall into three groups: joints and threaded hardware for links, weld-on steel such as perches, shock mounts, gussets and trusses, and rebuild parts for joints already on the truck. Tools cover axle, suspension and wiring work. Before buying joints, write down the thread size and hand, bolt diameter and housing width you need, so every part of a link matches.
Shop fabrication parts and tools
More part types (11)
Popular fabrication parts
-
Flex Joints
Rubicon Express Super-Flex Joint Rebuild Kit – RE3793
- Billet Super-Flex cartridge for the factory upper control arm mounts on Jeep XJ, MJ, ZJ, TJ and WJ chassis
- UHMW side races and a threaded adjuster nut
- Billet construction
- Rubicon says factory rubber bushings need replacing every race; this joint uses UHMW races instead
- Part number RE3793
SKU: R/ERE3793 -
-
Flex Joints
Rubicon Express Super-Flex Assembly – RE3791
- Weld-on Super-Flex joint cartridge for upper control arm mounts
- Fits the XJ, MJ, ZJ, TJ and WJ Jeep chassis
- UHMW side races and a threaded adjuster nut for tightening and rebuilding
- Serviceable, with a rebuildable joint
- Part number RE3791, UPC 614901440928
SKU: R/ERE3791 -
-
Shock Mounts
Rubicon Express Shock Mount – RE9957
- Pair of front axle brackets, designed as a shock mount, for 2007–2017 Jeep Wrangler JK
- Laser cut from 1/4 and 3/16 inch cold rolled steel and CNC formed
- For front Dana 30 and Dana 44 axles, 2- and 4-door models
- Bare steel, welding required
SKU: R/ERE9957 -
Axle Truss
G2 Dana 44 Front Axle Truss – 68-2051
- Front Dana 44 axle truss and armor system for the Jeep Wrangler JK
- Heavy-duty steel: 1/4 inch main components, 1/8 inch reinforcement plates
- Includes the axle truss, lower control arm skids, inner C gussets and track bar bracket
- Welding required, including to the cast center section
SKU: G/268-2051
Thread, joint and tool reference
Rod ends, jam nuts and tube adapters for off-road links use fine (UNF) threads. The sizes below are standard thread pitches, plus specs taken from listings in this category.
Standard fine-thread sizes
| 1/2" rod end or jam nut | 1/2"-20 UNF |
|---|---|
| 5/8" rod end or jam nut | 5/8"-18 UNF |
| 3/4" rod end or jam nut | 3/4"-16 UNF |
| 7/8" rod end or jam nut | 7/8"-14 UNF |
| 1-1/4" joint or jam nut | 1-1/4"-12 UNF |
Tools and the jobs they do
| Size or spec | Used for | |
|---|---|---|
| Spindle nut socket | 2-1/16" thin-wall deep | Dana 25, 27 and 30 hubs |
| Spindle nut wrench | Four prong | Spindle lock nuts |
| Trail Gear axle socket | 54 mm | Axle and hub nuts |
| Super-Flex assembly tools | 1/2" drive, small or large | RE Super-Flex joints only |
| Rancho bushing tool | 3-piece set | RS881015 bushings, JK/TJ |
| Torsion key tool | Puller style | Unloading torsion bars |
| Knuckle pull scale | Measures turning effort | Setting knuckle shims |
| Spanner wrenches | Preload spanners | Icon and Fox 2.5 coil-overs |
| Nutsert tool set | 10 pieces | Threaded inserts in sheet metal |
| Torx bit set | T15–T55 with tamper-proof | Jeep top and door Torx bolts |
Hardware specs from listings
| Rubicon Express jam nut | 3/4", 16 TPI, left-hand |
|---|---|
| Currie jam nut | 1.25"-12 left-hand, zinc plated |
| Rubicon Express female heim | 1/2", right-hand, sold singly |
| Super-Flex spherical balls | 1/2" and 9/16" sizes |
| Rubicon Express spring perch | For 2.5" wide springs, weld-on |
| Large Super-Flex race | Lower control arms, pair |
| Small Super-Flex race | Upper control arms, pair |
Weld-on parts in the listings
- Spring perches: weld to the axle tube, sold as a pair
- G2 Dana 44 front truss: unpainted, includes gusset, truss and bracket
- JK shock mounts: laser cut, bare steel, for Dana 30 and Dana 44, pair
- Gussets and tabs: weld-on reinforcement for brackets and cages
- Steering rod bungs: weld into tube to accept threaded ends
- Roll cage anchor plates: spread cage loads into the body
Thread a jam nut onto every adjustable end and keep full thread engagement in the tube. Recheck link and joint torque after the first trail run.
All Fabrication & Tools 504 parts
-
-
-
Axle Bracket Kits
Tuff Country Radius Arm Kit with Mounting Brackets – 24863
- Tuff Country radius arm kit with mounting brackets, part T/C24863
- Extended length radius arms for the 1983-1997 Ford Ranger
- Sharper turning radius and higher ground clearance, per the maker
- Longer wheel travel and increased suspension articulation
- Direct fit for 1983-1997 Ford Ranger trims
SKU: T/C24863 -
Axle Truss
Trail Gear Rock Assault Nine Axle Truss – 302552-KIT
- Rock Assault Nine axle truss, part number TGI302552-KIT, from Trail Gear
- Short specifications list the truss as rear
- Fits 1985 to 1995 Toyota 4Runner, 1979 to 1995 Toyota Pickup and 1995 to 2004 Toyota Tacoma
- Direct fit for the Toyota vehicles covered
SKU: TGI302552-KIT -
Axle Truss
Trail Gear Rock Assault Axle Truss – 302549-1-KIT
- Rock Assault axle truss, part number TGI302549-1-KIT, for axle housing protection
- Fits 1985 to 1995 Toyota 4Runner, 1979 to 1995 Toyota Pickup and 1995 to 2004 Toyota Tacoma
- Confirm front or rear axle position before ordering
- Built for use with an OEM axle
SKU: TGI302549-1-KIT
What you will find here
Fabrication and tools covers the small parts that custom suspension and chassis work depends on. Rod ends and flex joints let links articulate, tube adapters join tubing to those joints, gussets and tabs reinforce brackets, and perches and shock mounts attach springs and shocks to axles and frames. Specialty tools such as joint presses, torsion key unloaders, spindle nut sockets and installation tools round out the category.
Rod ends and flex joints
Johnny Joint style flex joints use a bushing in a threaded housing, usually with urethane, and allow articulation while absorbing vibration. Heim joints, often called rod ends, use a spherical ball and are more rigid and precise, but they transmit more noise and need regular inspection. Left-hand and right-hand threaded ends, paired with jam nuts, let you adjust link length without removing the link. Misalignment spacers let a joint swing through its full range without binding.
Specs to match
- Thread size and direction: for example 3/4 inch versus 1-1/4 inch, left or right hand.
- Housing outside diameter and mounting width: this must match the tube or bracket.
- Bolt hole size: sets the bolt diameter through the joint.
- Weld-on or threaded: some adapters and joints must be welded.
- Serviceability: some joints grease through a fitting, and some can be rebuilt.
Safety and workmanship
Suspension links, cage components and steering parts are safety-critical. Welding should be done by someone qualified, using correct tube wall thickness, proper penetration and heat control. Use proper-grade hardware, tighten to specification, and fit jam nuts correctly with full thread engagement. Inspect joints regularly for play and cracks. For steering and suspension work you are unsure about, have a professional fabricator build and inspect it.
Think about the complete link before buying individual parts. A control arm or link is built from two ends, a tube and the hardware, and every piece must match: the thread of the ends has to match the tube adapter, and the bolt diameter must match the mounts on the axle and frame. Measure the center-to-center length you need with the suspension at ride height and again at full droop and full compression, so the ends never bind or run out of thread engagement.
The tools in this category make jobs safer and tidier. Joint presses and installation tools prevent damaged bushings, and a spindle nut socket or torsion key tool does a job that is awkward and risky with improvised tools. Brackets, gussets and tabs should be welded with clean, fully fused beads and placed to spread loads into the surrounding structure rather than concentrating stress on a single spot. Never grind or drill structural components without understanding how that changes their strength. Keep a record of the torque used on every fastener and recheck after the first trail outing.
Keep spare hardware on hand for trail repairs, including a few jam nuts, grade-rated bolts, nylon-insert locknuts and extra misalignment spacers, since these small parts are easy to lose and hard to improvise. Mark the final position of each adjustable end with paint so you can see at a glance if anything has turned. Store rod ends clean and lightly oiled, because rust inside a spherical bearing causes binding and premature wear.
Compatibility
Many items here are universal, so fitment depends on your design. Confirm dimensions and thread specifications from the manufacturer before choosing a product below.
Popular Fabrication & Tools brands
- Artec Industries (94)
- Rubicon Express (72)
- RockJock 4x4 (56)
- Currie (52)
- Trail Gear (44)
- TeraFlex (31)
- Fabtech (26)
- Blue Torch Fabworks (23)
- Rock Krawler (18)
- Mountain Off Road Enterprises (15)
- Pro Comp Suspension (13)
- Poison Spyder Customs (13)
Fabrication & Tools FAQ
What is a Johnny Joint?
A Johnny Joint is a trademarked style of flex joint that places a bushing inside a threaded housing so a link or arm can pivot and twist. It is quieter than a heim joint and widely used in control arms and track bars.
What is the difference between a heim joint and a flex joint?
A heim joint uses a metal spherical bearing for precise, rigid movement, but it can be noisy and needs inspection. A flex joint uses a bushing, often urethane, which dampens noise and vibration while still letting the link articulate.
Why do rod ends come in left-hand and right-hand threads?
Pairing one left-hand and one right-hand end lets you turn a single link tube to lengthen or shorten it without removing either end. Jam nuts then lock the adjustment so the threads cannot back out.
Do I need to weld tube adapters?
Many tube adapters and weld-in joints must be welded to the tubing, while others thread in. Check the product description. Welding structural suspension parts should be done by a qualified fabricator using suitable tube material and technique.





























