Select your vehicle

TeraFlex SpeedBump Bumpstop Kit – 1958260

TeraFlex

$443.99In stock
Buy on Amazon

See similar parts on Amazon

Price and availability as of Nov 17, 2026 11:20 AM MST, from Amazon.com, and subject to change. The Amazon listing has the current details.

Check out with your Amazon account. Amazon handles delivery and returns.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rear SpeedBump bump stop kit for 2007–2015 Jeep Wrangler (JK)
  • Includes two 3-inch travel SpeedBump bump stops
  • Rear weld-in mounting sleeves with integrated clamp
  • Includes rear lower bump stop strike pads and brackets

Description

Overview

The TeraFlex SpeedBump Bumpstop Kit 1958260 is a rear bump stop kit for 2007–2015 Jeep Wrangler (JK) models. It uses two 3-inch travel SpeedBump bump stops that compress progressively, so a hard suspension stroke is cushioned instead of hitting the stop abruptly.

A progressive bump stop builds resistance as it is compressed. These SpeedBumps are made from closed-cell, nitrogen-charged microcellular polyurethane designed to resist fading under extended heavy use and to stay flexible at extreme temperatures, including sub-zero conditions. The kit is designed to reduce the harsh bottoming felt on off-road trails and rough highways.

The rear kit includes weld-in mounting sleeves with an integrated clamp, plus rear lower bump stop strike pads and brackets. Because the sleeves are welded in, this is a fabrication project rather than a bolt-on swap.

Key features

  • Two 3-inch travel SpeedBump bump stops for rear applications
  • Closed-cell, nitrogen-charged microcellular polyurethane body
  • Progressive compression intended to reduce harsh bump stop bottoming
  • Delrin acetal resin shaft designed to be self-lubricating over thousands of cycles.
  • External shaft seal that wipes and cleans the shaft against contaminants
  • Maintenance free, with no custom adjustment or tuning needed

Rear travel and welded installation

On a rear axle, the bump stop is often the component that takes the largest hits on washboard roads and drops off ledges. A progressive stop starts to resist early in its travel, which can take some of the sharp edge off an impact before the axle reaches the frame. Rear stops should be checked alongside the springs, since spring rate and remaining droop both affect when the stop engages.

Because this kit uses weld-in sleeves, plan the install as a fabrication job. Clean the mounting surfaces, mark locations with the vehicle at ride height, and have someone check sleeve alignment before the final welds. A fabricator can also judge whether the frame section is sound enough for the added load.

  • Inspect shaft seals for dirt or grit after rough runs
  • Check the clamp and sleeve for movement each season
  • Look for cracked or flattened polyurethane bodies
  • Keep the upper stop mounting area free of mud buildup

Specifications

Brand TeraFlex
Part number 1958260
UPC 843885025108
Position Rear
Listed type Rubber bump
Travel 3 inches each
Shaft Delrin acetal resin, self-lubricating
Body Closed-cell nitrogen-charged microcellular polyurethane
Fitment type Direct fit

Vehicle fitment

It fits 2007–2015 Jeep Wrangler (JK) models, including the 70th Anniversary, Rubicon, Sahara, Sport and X trims, and the Unlimited versions of those trims.

Wrangler TJ, LJ and JL vehicles are not covered. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Installation requires removing the front factory bump stop bell and extensive frame modification to fit the mounting sleeve. Welding is required, so this kit is best installed by a qualified fabricator or a shop with weld-capable equipment. Work on a lifted suspension only with the vehicle properly supported.

What’s included

Two 3-inch travel SpeedBump bump stops, two rear weld-in mounting sleeves with integrated clamp, rear lower bump stop strike pads and brackets.

Not included: Welding equipment and the fabrication labor that the installation requires.

SKU: TER1958260 Category:

Specification

Shipping weight 9.00 lbs
Package dimensions 12.00 × 8.20 × 6.50 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (JK)2007–201570th Anniversary, Rubicon, Sahara, Sport, Unlimited 70th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X, X

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the TeraFlex 1958260 fit my 2007–2015 Jeep Wrangler JK?

It fits 2007–2015 Jeep Wrangler (JK) models across the Rubicon, Sahara, Sport, X and Unlimited trims. Check your year, model and trim before buying.

Does this kit bolt on?

No. Installation requires removing the front factory bump stop bell and extensive frame modification, and welding is required to install the mounting sleeves.

How many bump stops come in the kit?

The kit includes two 3-inch travel SpeedBump bump stops, two rear weld-in mounting sleeves with integrated clamp, and rear lower bump stop strike pads.

What signs show a bump stop needs replacing?

Look for cracks, missing chunks, flattened or torn polyurethane, and a shaft that feels gritty or sticks. Harsh bottoming that did not happen before is another sign. Replace worn stops in pairs so both sides engage the same way.

Ready to order?

Order this part on Amazon and check out with your Amazon account. Amazon handles delivery and returns.

Buy on Amazon