Select your vehicle
-13%

Pro Comp PRO-M Monotube Front Shock Absorber – PR2084

Pro Comp Suspension

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Pro Comp PRO-M front monotube shock, part PR2084, sold individually
  • Designed for 1.5 to 3 inches of lift
  • Extended 24.5 in, collapsed 15.4 in
  • Fits the 2007 to 2018 Jeep Wrangler JK, two-door and four-door

Description

Overview

The Pro Comp Suspension PR2084 is a PRO-M front monotube shock for Jeep Wrangler JK models with 1.5 to 3 inches of lift. It fits the 2007 to 2018 Wrangler JK in two-door and four-door models, and it is sold individually.

The shock uses a nitrogen gas charge that helps limit cavitation, with a floating piston and multi-stage valving set for the vehicle. The 2 inch body holds more oil to dissipate heat during off-road use.

Key features

  • Front monotube design for 1.5 to 3 inches of lift
  • Extended length 24.5 inches, collapsed length 15.4 inches
  • 2 inch diameter body
  • Nitrogen gas charged with floating piston
  • Polyurethane shock boot included

Lift height and front springs

A 1.5 to 3 inch lift on a JK changes the front spring position and the angle the shock works through. Because the body is two inches wide, it needs room to move past the spring at full compression, so check that gap before final assembly. Shocks sized for a particular lift range are usually matched to the spring rate and ride height that suit that setup.

Front shocks on a JK are often replaced along with the track bar, control arm bushings and bump stops when a truck has covered rough terrain. Worn parts can make a new damper feel harsh or wandering because the steering and suspension geometry no longer match. Recheck the front alignment after any lift change so tire wear stays even.

  • Confirm the spring clearance at full compression
  • Replace worn bushings before fitting a new damper
  • Recheck alignment after the lift is set

Specifications

Brand Pro Comp Suspension
Part number EXPPR2084
Shock series PRO-M
Position Front
Body diameter 2 in
Extended length 24.5 in
Collapsed length 15.4 in
Upper and lower mount Loop
Lift 1.5 to 3 in
Finish Silver powder coat

Vehicle fitment

It fits the 2007 to 2018 Jeep Wrangler (JK), including the 70th and 75th Anniversary, Rubicon, Sahara, Sport, Sport S and X models in two-door and four-door bodies.

It is designed for the JK generation only. Confirm fit for your vehicle’s year, model and trim before ordering.

Installation notes

Compare the 24.5 inch extended and 15.4 inch collapsed lengths with the front shock being replaced, since a lift in the 1.5 to 3 inch range changes the ride height on a JK. The loop mounts should line up with the factory brackets, and the 2 inch body needs clearance from the front spring at full compression. Check the boot after installation and after the first drive on rough ground.

Measure the truck’s height before fitting, since the shock is designed for 1.5 to 3 inches of lift. Check the loop mounts are tight, confirm the body clears the front spring at full compression, and inspect the boot after the first drive.

Check the front shock is clear of the steering linkage and the brake hose at full lock, and confirm the boot does not rub against the spring.

What’s included

One PRO-M front monotube shock with polyurethane boot under part number EXPPR2084.

Fitment

VehicleYearsTrims
Jeep Wrangler (JK)2007–201870th Anniversary (2-Door), 75th Anniversary (2-Door), Rubicon (2-Door), Sahara (2-Door), Sport (2-Door), Sport S (2-Door), Unlimited 70th Anniversary (4-Door), Unlimited 75th Anniversary (4-Door), Unlimited Rubicon (4-Door), Unlimited Sahara (4-Door), Unlimited Sport (4-Door), Unlimited Sport S (4-Door), Unlimited X (4-Door), X (2-Door)

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the PR2084 fit a 2012 Jeep Wrangler JK Unlimited?

Yes. It fits the 2007 to 2018 Wrangler JK, including four-door Unlimited models in the 70th Anniversary, 75th Anniversary, Rubicon, Sahara and Sport trims. Confirm fit for your vehicle's year, model and trim before ordering.

Is the PR2084 for a lift of 1.5 to 3 inches?

Yes. It is designed for 1.5 to 3 inches of lift, with a 24.5 inch extended length and a 15.4 inch collapsed length. Compare these lengths with the front shock being replaced before fitting, since lift changes ride height.

Does the PR2084 fit a TJ?

No. It is built for the 2007 to 2018 JK generation, so the TJ and LJ are not a fit for this part number. Confirm fit for your vehicle's year, model and trim before ordering.

Should bump stops be replaced with a new front shock?

Inspect bump stops whenever the front shocks are replaced. Worn or cracked bump stops can let the axle hit the frame at full compression, and the new shock can then take loads it was not designed for. Replacing them at the same time is a practical step on a JK.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon