Select your vehicle
-13%

G2 XJ Cherokee Front and Rear 4.56 Ring and Pinion Kit – 4-XJ5-456

G2 Axle and Gear

Shop Jeep Cherokee XJ Ring And Pinions on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • 4.56 front and rear ring and pinion kit for the Cherokee XJ
  • Dana 30 reverse front, Chrysler 8.25 rear
  • Front and rear matched master installation kits
  • Part number 4-XJ5-456, 1984–2001

Description

Overview

The G2 4-XJ5-456 is a front and rear 4.56 ring and pinion kit for the 1984–2001 Jeep Cherokee (XJ), with a Dana 30 reverse front and a Chrysler 8.25 rear axle. It includes everything needed for a gear swap.

The set includes matched master installation kits for both axles and 4.56 gears at each end. The kit carries a limited lifetime warranty. The gears are computer heat treated 8620 steel, manufactured to O.E. specs, double shot peened and double lapped.

Key features

  • 4.56 gears front and rear
  • Dana 30 reverse front, Chrysler 8.25 rear
  • Matched master installation kits
  • Fits 1984 to 2001 XJ Cherokee
  • Limited lifetime warranty

Before a gear swap

Changing ring and pinion gears alters the final drive ratio, which changes how the vehicle accelerates, how it pulls at low speed and how it cruises on the highway. Tire size and the transmission and transfer case behind the axles are often considered together, so a regear is usually planned around the whole driveline before the gears are ordered.

Gear sets are only as good as the bearings, carrier and pinion setup behind them. Old bearings and seals are commonly replaced during a regear because they are disturbed during the job. Check the pinion and carrier bearings, the axle seals and the differential bearings for wear before reassembly, and replace any part that shows roughness or play.

After installation, the first miles matter. Keep speeds moderate during break-in, check the gear mesh and fluid level after the first trips, and listen for whine or clunks. Use the gear oil suited to the axle type, and refill with the correct lubricant.

Specifications

Brand G2 Axle and Gear
Part number 4-XJ5-456
UPC 700007521841
Product type Front and rear ring and pinion sets with master installation kits
Gear ratio 4.56
Front axle gears Dana 30 reverse 4.56
Front carrier 3.73 and up
Rear axle gears Chrysler 8.25in 4.56
Installation kits Front and rear matched master installation kits
Material Computer heat treated 8620 steel
Manufacturing Manufactured to O.E. specs, double shot peened, double lapped
Warranty Limited lifetime warranty

Vehicle fitment

The 4-XJ5-456 fits the 1984 to 2001 XJ Cherokee with a Dana 30 reverse front axle and a Chrysler 8.25 rear axle.

The 4-XJ5-456 does not cover an XJ with a Dana 35 rear or a Dana 30 short front, or other Jeep models. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Fitting the 4-XJ5-456 means setting pinion depth, preload and backlash twice, using the master installation kits. The front gears want a 3.73 and up carrier. Gear setup and break-in are best done by an experienced installer.

What’s included

  • Front ring and pinion gear set
  • Rear ring and pinion gear set
  • Front matched master installation kit
  • Rear matched master installation kit

Not included: carriers and parts outside the two master installation kits.

SKU: G/24-XJ5-456 Category:

Specification

Shipping weight 39.00 lbs
Package dimensions 0.00 × 0.00 × 0.00 in
brands

Fitment

VehicleYearsTrims
Jeep Cherokee (XJ) likely fits1984–2001All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Is the G2 4-XJ5-456 for a Chrysler 8.25 rear?

Yes. The 4-XJ5-456 pairs a Dana 30 reverse front with a Chrysler 8.25 rear at a 4.56 ratio, for the 1984 to 2001 XJ Cherokee.

What is included in the 4-XJ5-456?

The kit has front and rear 4.56 gear sets plus front and rear matched master installation kits, one for each axle of the Cherokee.

What carrier does the 4-XJ5-456 front need?

The Dana 30 reverse front gears of the 4-XJ5-456 need a 3.73 and up carrier. Confirm the rear carrier for your Chrysler 8.25 axle before ordering.

Do the old bearings need replacing during a regear?

Often, yes. The bearings and seals are disturbed when the gears come out, and worn bearings can shorten the life of new gears. Inspect them before reassembly and replace any that show roughness, play or heat marks.

Can the front and rear sets be fitted separately?

It is best to change both axles together, since the sets are matched as a pair in this kit. Mixing a new gear ratio on one axle with an old ratio on the other leaves the two axles turning at different speeds, which can stress the driveline.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Cherokee XJ Ring And Pinions on Amazon