Overview
The G2 Axle and Gear 35-2023A is a master ring and pinion installation kit for the GM 14 Bolt 10.5 Inches rear axle.
The GM 14 bolt with the 10.5 inch ring gear is a heavy-duty rear axle, and the 35-2023A is its master kit for later builds. Besides the usual Timken pinion and carrier bearings, it adds a Timken pinion pilot bearing, and also provides shims, a crush sleeve, a nut and seal, bolts, and compounds.
The big 14 bolt is built to carry heavy loads, and its installation parts reflect that. G2 adds the Timken pinion pilot bearing here, in addition to the usual inner and outer pinion bearings and carrier bearings with races. Shims, a crush sleeve, a pinion nut and seal, ring gear bolts, thread locker, marking compound and sealer round out the master kit for 1988 and later axles.
Key features
- Master installation kit for the GM 14 Bolt 10.5 Inches axle (rear)
- Includes pinion Nut
- Includes pinion Seal
- Includes Timken Outer Pinion Bearing and Race
- Includes crush Sleeve
- Includes Timken Inner Pinion Bearing and Race
- Includes pinion Shims
- Includes Timken Pinion Pilot Bearing
- Includes carrier Shims
- Includes carrier Bearings and Races
Heavy-duty 14 bolt care
The 14 bolt is built for heavy loads, so the rebuild is a chance to check the whole rear end rather than only the gears. Look at the axle shaft bearings, the housing bores and the carrier cradle for wear or cracks. Replacing parts while the housing is open costs less than a second teardown later. Fresh bearings and races should match the pinion and carrier they seat against.
Gear setup on a big 14 bolt rewards patience. Set the pinion depth first, then the carrier preload, and use the marking compound to judge the pattern before final assembly. Clean every mating surface and use new seals where they are fitted, and fill the housing to the correct level once the setup is complete.
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 35-2023A |
| UPC | 631410095715 |
| Kit type | Master kit with bearings |
| Axle location | Rear |
| Axle type | GM 14 Bolt 10.5 Inches |
| Axle manufacturer | GM |
Vehicle fitment
The kit is made for 1988 and later big bearing GM 14 bolt 10.5 inch rear axles. Axles built from 1973 to 1987 need a different G2 kit, so check the build era of your housing before ordering.
Confirm your vehicle’s axle type, spline count and year before ordering.
Installation notes
The pilot bearing supports the tip of the pinion, so install it along with the main pinion bearings. As with any gear job, shim for the correct depth and use the marking compound to confirm the contact pattern.
Before opening the GM 14 Bolt 10.5 Inches housing for the 35-2023A job, gather a dial indicator, a torque wrench and clean gear oil. Record the original gear pattern, because the 35-2023A shims are the tool for moving the new pattern toward it. Fit the new nut and seal. Sort shims by thickness.
What’s included
- Pinion Nut
- Pinion Seal
- Timken Outer Pinion Bearing and Race
- Crush Sleeve
- Timken Inner Pinion Bearing and Race
- Pinion Shims
- Timken Pinion Pilot Bearing
- Carrier Shims
- Carrier Bearings and Races
- Ring Gear Bolts
- Thread Locking Compound
- Gear Marking Compound
- Silicone Sealer
Not included: ring and pinion gears; the 35-2023A supplies installation parts for the GM 14 Bolt 10.5 Inches axle only.













