Select your vehicle

G2 Dana 30/44 TJ/LJ 4.88 Ring and Pinion Minor Installation Kit – 4-TJ2-488M

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • 4.88 front Dana 30 and rear Dana 44 ring and pinion kit
  • For non-Rubicon 1997–2006 Wrangler TJ and LJ
  • Includes front and rear matched minor installation kits
  • Computer heat treated 8620 steel; limited lifetime warranty

Description

Overview

The G2 Axle and Gear 4-TJ2-488M is a complete 4.88 ring and pinion kit with minor installation kits for the Dana 30 front and Dana 44 rear axles of non-Rubicon 1997–2006 Jeep Wrangler TJ and LJ models.

Non-Rubicon TJ and LJ owners can regear both axles with matched sets from G2. The kit supplies 4.88 gears for the Dana 30 front and Dana 44 rear, along with a minor installation kit for each axle. The gears are double lapped, double shot peened, computer heat treated 8620 steel made to O.E. specs.

TJ and LJ Wranglers from the factory used a Dana 30 front and Dana 44 rear on most non-Rubicon models, which is what this kit expects. A swap to 4.88 gears brings back the acceleration that bigger tires take away. Because both axles are changed together, the front and rear ratios stay matched. The LJ is the longer wheelbase Unlimited version of the TJ, which G2 includes in the same description.

Key features

  • Front and rear 4.88 gear sets
  • Dana 30 front and Dana 44 rear
  • Non-Rubicon models
  • Matched minor installation kits
  • Manufactured to O.E. specs
  • Limited lifetime warranty.

Pinion setup and break-in

A ring and pinion swap changes the gear mesh inside each axle, so the pinion depth and backlash have to be set before the carrier goes back in. Matched front and rear sets keep the two axles turning at the same ratio, which keeps four-wheel drive working as intended. Gear swaps are usually done in one session so both axles are checked against each other.

Break-in matters as much as setup. Early miles should be easy, with moderate throttle and varied speeds, and the fluid level should be checked afterward. Because a lower ratio changes engine speed at a given road speed, the transmission and transfer case will also run differently after the change.

  • Set pinion depth and backlash before final assembly
  • Check the gear contact pattern on each axle
  • Replace seals and bearings when the carrier is opened
  • Recheck fluid level after the first drives

Specifications

Brand G2 Axle and Gear
Part number 4-TJ2-488M
UPC 631410141221
Part type Ring and pinion gear kit with minor installation kits
Gear ratio 4.88
Axles Dana 30 front, Dana 44 rear
Models Non-Rubicon
Steel Computer heat treated 8620
Finishing Double shot peened, double lapped
Warranty Limited lifetime

Vehicle fitment

It fits non-Rubicon 1997–2006 Jeep Wrangler TJ and LJ models.

It does not fit Rubicon TJ or LJ models, which use different axles. Before ordering, confirm fit for your vehicle’s year, model and trim.

Installation notes

Setting up a gear swap properly requires pinion depth and backlash work, and a break-in period afterward. Confirm your Wrangler has the Dana 30 and Dana 44 combination first.

What’s included

  • Front 4.88 ring and pinion set
  • Rear 4.88 ring and pinion set
  • Front and rear matched minor installation kits

Not included: Bearings and other parts beyond the minor kits, so verify the full parts list before starting.

SKU: G/24-TJ2-488M Category:

Specification

Shipping weight 31.00 lbs
Package dimensions 0.00 × 0.00 × 0.00 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (LJ) likely fits2004–2006All
Jeep Wrangler (TJ) likely fits1997–2006All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What Jeep does the G2 4-TJ2-488M fit?

G2 names the 97-06 Wrangler TJ/LJ, non-Rubicon models, with a Dana 30 front and Dana 44 rear axle combination in the same truck.

What ratio is the 4-TJ2-488M?

4.88, for both the front and rear gear sets, which are matched so the two axles turn together properly in four-wheel drive.

Does it fit a TJ Rubicon?

No. G2 lists non-Rubicon models only, because Rubicon axles differ from the Dana 30 front and Dana 44 rear this kit is built around.

What is included?

Front and rear 4.88 ring and pinion sets, plus a matched minor installation kit for each axle. Compare the included parts with your installation plan before starting, especially the minor kit parts.

How should the new gears be broken in?

Keep early driving easy, with moderate throttle and a mix of speeds rather than long highway runs under heavy load. Check the fluid level and look for leaks after the first drives, then once more after the break-in period.

Should the transfer case or driveshaft be checked after a gear swap?

Yes. A lower ratio changes engine speed at a given road speed, so the transmission and transfer case work differently afterward. Inspect U-joints and the driveshaft for wear while the drivetrain is accessible.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon