Select your vehicle

G2 Ford 9 Inch 3.70 Ratio Ring and Pinion – 2-2011-370

G2 Axle and Gear

Shop G2 Axle And Gear Ring And Pinions on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • G2 Axle and Gear 3.70 ratio ring and pinion for the Ford 9 inch rear axle, part 2-2011-370
  • Rear axle location
  • Universal fit listed by axle type
  • Suited to oversized tires and high performance engines.

Description

Overview

The G2 Axle and Gear 2-2011-370 is a 3.70 ratio ring and pinion for the Ford 9 inch rear axle. It is made for the rear location and suits the Ford 9 inch axle type.

G2 describes its performance ring and pinion sets as engineered for oversized tires and high performance engines, made with the latest technology and materials. The 3.70 ratio gives more torque multiplication at the wheels than a 3.50 set.

Key features

  • 3.70 ratio rear ring and pinion
  • Ford 9 inch rear axle type
  • Built for oversized tires and high performance engines.
  • Manufactured with the latest technology and materials.

Trail and towing use

A 3.70 ratio adds pulling force at the wheels, which helps on steep grades, loose surfaces and loaded trailers. The cost is higher engine speed at cruising and somewhat more fuel use on the highway, so the gearing suits drivers who spend time off pavement.

Heavier-duty use puts more load on the pinion bearing and the carrier, so those parts deserve a look when the gears are changed. Setting pinion depth, backlash and preload correctly keeps the new teeth from running hot or wearing early. Comparing the new ratio with the existing set before the job helps confirm the change is worth it for your tire size and typical load.

  • Recheck fluid level after rough trail use
  • Inspect the axle vent for water intrusion
  • Replace the pinion seal during the install
  • Look for uneven tooth wear at each service

Specifications

Brand G2 Axle and Gear
Part number 2-2011-370
UPC 631410105414
Gear ratio 3.70
Axle location Rear
Axle type Ford 9 inch
Popular axle manufacturer Ford

Vehicle fitment

This 3.70 set is not tied to a particular vehicle model or year. It is built for the Ford 9 inch at a 3.70 ratio, so confirm the housing size before ordering.

Only the Ford 9 inch is named for this 3.70 set. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Pinion depth, backlash and bearing preload on the 3.70 Ford 9 inch gears should be set by a driveline shop before the axle is run in.

What’s included

A 3.70 ring and pinion set for the Ford 9 inch.

SKU: G/22-2011-370 Category:

Specification

Shipping weight 25.00 lbs
Package dimensions 12.00 × 11.00 × 5.50 in
brands

Questions & Answers

Does 2-2011-370 fit a Ford 9 inch rear axle?

The set is built for the Ford 9 inch rear axle in the rear location at a 3.70 ratio. Verify the housing and the vehicle's model year and trim before the order goes in.

What ratio is this set?

It is a 3.70 ratio ring and pinion set. It gives more torque multiplication at the wheels than a 3.50 ratio.

Is a carrier named for it?

No carrier is named for this set. Confirm the carrier and ratio before installing, and have a driveline shop set pinion depth and backlash.

Does the axle need to be rebuilt when new gears are installed?

Not always, but worn bearings, seals and a damaged carrier should be replaced at the same time. Inspect those parts when the gears are out, since reusing worn components can shorten the life of the new set.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop G2 Axle And Gear Ring And Pinions on Amazon