Select your vehicle
-13%

G2 Ford 7.5 Inch Replacement Axle Shaft – 95-2014-002

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits 1983–1992 Ford Ranger, rear driver side
  • Ford 7.5 inch axle, 28 splines
  • 1/2 inch press-fit studs, not included

Description

Overview

The G2 Axle and Gear 95-2014-002 is a rear driver-side replacement axle shaft for the Ford 7.5 inch axle in the 1983–1992 Ford Ranger. It has 28 splines and takes 1/2 inch press-fit wheel studs.

The shaft is made from forged alloy steel and heat treated to exceed OEM specifications. It is designed to withstand more torque than the factory part and to address common shaft failures.

The 95-2014-002 is made for the Ford 7.5 inch rear axle, the smaller of the Ford rear ends used under the Ranger. With 28 splines and 1/2 inch press-fit wheel studs, it uses the same shaft format as other G2 Axle and Gear shafts, and its alloy steel is forged and heat treated beyond OEM specifications.

Key features

  • Driver-side rear shaft for the Ford 7.5 inch axle
  • 28 splines
  • 1/2 inch press-fit wheel studs
  • Forged alloy steel
  • Wheel studs not included

Ranger rear axle basics

The Ford 7.5 inch axle used under the Ranger is a compact rear end, and its shafts are short and tightly packed around the differential. Because the space is limited, a replacement shaft must seat fully in the side gear and sit square against the bearing retainer. Look for uneven wear on the splines and a bearing that feels loose, since either can make a new shaft click or bind.

Rust is a frequent issue on older Rangers, particularly around the axle tube and the bearing area. Wire brush and clean the mating surfaces before installing, and use fresh gasket or sealant where the retainer meets the housing. Press-fit studs need a proper press tool, so plan the job with the right equipment on hand.

Specifications

Brand G2 Axle and Gear
Part number 95-2014-002
UPC 631410105698
Product type Replacement axle shaft
Axle type Ford 7.5 inch
Axle location Rear
Shaft position Driver Side
Spline count 28
Press-fit wheel stud size 1/2 inch
Wheel studs Not included
Stated application 1983-1992 Ford Ranger driver side

Vehicle fitment

It fits the 1983–1992 Ford Ranger. Other Ford trucks are outside this fit, so confirm your vehicle’s year, model and trim before ordering.

The list stops at 1992, and it names the Ranger only, so other Ford trucks are not covered. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

  • Plan on 1/2 inch press-fit studs, which are not part of this shaft.
  • Check that your 7.5 inch axle uses 28-spline gears.

What’s included

One driver-side rear axle shaft (95-2014-002).

Not included: wheel studs for the 95-2014-002.

SKU: G/295-2014-002 Category:

Specification

Shipping weight 22.00 lbs
Package dimensions 37.00 × 7.50 × 7.30 in
brands

Fitment

VehicleYearsTrims
Ford Ranger1983–1992Base, Custom, GT, S, S Plus, STX, Sport, XL, XLS, XLT

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What Ranger years does the G2 95-2014-002 fit?

It fits the 1983–1992 Ford Ranger. It is a driver-side rear shaft made for the Ford 7.5 inch axle, with 28 splines.

Which Ford axle is the 95-2014-002 made for?

It is made for the Ford 7.5 inch rear axle and sits on the driver side. It fits the 1983–1992 Ranger, so check your axle size before ordering.

How many splines does the 95-2014-002 have?

It has 28 splines. Your differential side gears should match that spline count for the shaft to engage properly. The 95-2014-002 has 28 splines for the Ford 7.5 inch axle and sits on the driver side.

Does the 95-2014-002 include wheel studs?

No, G2 says wheel studs are not included. The shaft accepts 1/2 inch press-fit studs that you supply separately. The 95-2014-002 has 28 splines for the Ford 7.5 inch axle and sits on the driver side.

Can a bent axle shaft be straightened?

No. A bent shaft should be replaced, because straightening can leave hidden stress in the steel and lead to a later break. Bends often come from a hard impact or a failed hub bearing.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon