Select your vehicle

G2 Ford 7.5 Inch Master Ring and Pinion Installation Kit – 35-2014

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Master kit with bearings for the Ford 7.5-inch axle, rear
  • Pinion and carrier bearings with shims, nut, seal and crush sleeve
  • Includes Timken pinion bearings and carrier bearings, shims, nut, seal and crush sleeve
  • Gear marking compound, thread locking compound and silicone sealer

Description

Overview

The G2 Axle and Gear 35-2014 is a master ring and pinion installation kit with bearings for the Ford 7.5-inch rear axle.

The 35-2014 follows G2’s master kit approach: it includes the parts needed to properly install a ring and pinion, with pinion bearings and carrier bearings along with the shims, nut, seal and compounds. G2 says some of the parts in the 35-2014 are hard to find items that auto parts stores rarely stock. The 35-2014 does not contain the ring and pinion gear set itself.

Key features

  • Master kit with bearings for the Ford 7.5-inch axle
  • Timken outer and inner pinion bearings and races
  • Pinion shims and carrier shims
  • Carrier bearings and races included
  • Pinion nut, crush sleeve, pinion seal and ring gear bolts
  • Thread locking compound, gear marking compound and silicone sealer

Gear setup basics

A master kit covers the bearings and small parts, but the gear setup still decides how well the new set lasts. Pinion depth, carrier preload and the tooth contact pattern are set with shims, crush sleeve and marking compound. Rushing these steps can cause early wear, noise or a loose gear mesh. An installer with gear setup experience can check each setting against the carrier and gear set before final assembly.

Good preparation helps the job go smoothly. Clean the housing and carrier thoroughly, and inspect the bearing bores for damage before pressing in new races. Keep the shims in order as they come off, since their stack determines the pinion setting. Tighten the pinion nut gradually and check preload with a torque-measuring tool as you go, rather than trusting a single figure.

  • Clean the housing and bearing bores
  • Keep shims in their original order
  • Check the contact pattern before final assembly

Specifications

Brand G2 Axle and Gear
Part number 35-2014
UPC 631410095593
Product type Master ring and pinion installation kit with bearings
Axle Ford 7.5-inch
Axle location Rear
Popular axle manufacturer Ford
Kit type Master kit with bearings
Contents Pinion nut, pinion seal, Timken outer pinion bearing and race, crush sleeve, Timken inner pinion bearing and race, pinion shims, carrier shims, carrier bearings and races, ring gear bolts, thread locking compound, gear marking compound, silicone sealer

Vehicle fitment

The 35-2014 is made for the Ford 7.5-inch axle in the rear position. It is identified by axle rather than by vehicle make, model or years, so confirm the vehicle fit before ordering. Check the axle and carrier against your installation before starting.

It is made for the Ford 7.5-inch axle only, not other axle designs or sizes. Check your year, model and trim before ordering.

Installation notes

A master kit such as the 35-2014 rebuilds the gear setup completely, so the bearings are replaced along with the gear set. The pinion shims, carrier shims, crush sleeve and gear marking compound in the 35-2014 are the parts used to set pinion depth, preload and the tooth contact pattern, which calls for an installer with gear setup experience and a careful break-in afterwards.

What’s included

  • Pinion nut
  • Pinion seal
  • Timken outer pinion bearing and race
  • Crush sleeve
  • Timken inner pinion bearing and race
  • Pinion shims
  • Carrier shims
  • Carrier bearings and races
  • Ring gear bolts
  • Thread locking compound
  • Gear marking compound
  • Silicone sealer

Not included with the 35-2014: ring and pinion gear set.

SKU: G/235-2014 Category:

Specification

Shipping weight 7.00 lbs
Package dimensions 12.90 × 12.80 × 3.10 in
brands

Questions & Answers

What axle is the G2 35-2014 for?

The 35-2014 is a master installation kit with bearings for the Ford 7.5-inch axle. The 35-2014 listing gives the axle location as rear. The 35-2014 is described by axle and does not replace the ring and pinion gear set.

What is included in the G2 35-2014 kit?

The 35-2014 kit includes pinion nut, pinion seal, Timken outer pinion bearing and race, crush sleeve, Timken inner pinion bearing and race, pinion shims, carrier shims, carrier bearings and races, ring gear bolts, thread locking compound, gear marking compound and silicone sealer.

Does the 35-2014 include the ring and pinion gears?

No. The kit contains installation parts and bearings only, with no ring and pinion gear set, so you need to source the gears separately. Check the gear set against your carrier before buying.

Is the 35-2014 for a front or rear axle?

It is made for the rear Ford 7.5-inch axle. Confirm the axle is the rear 7.5-inch unit in your vehicle, and check your year, model and trim before ordering.

Can I reuse the old bearings with the new gears?

Replacing them is the sensible choice. The kit supplies new Timken pinion and carrier bearings, and bearings that ran with worn gears may already carry wear that shortens the life of the new set. Inspect any old bearing for pitting or roughness before deciding.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon