Select your vehicle
-13%

G2 Chrysler 8.25 Inch Master Ring and Pinion Installation Kit – 35-2029

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • For Chrysler 8.25 inch rear axles with 27 or 29 spline axles
  • Timken pinion and carrier bearings with races
  • Shims, crush sleeve, pinion seal and nut
  • Part number 35-2029

Description

Overview

The G2 Axle and Gear 35-2029 is a master ring and pinion installation kit for the Chrysler 8.25 Inches rear axle.

The Chrysler 8.25 inch rear axle gets its master installation parts in the 35-2029. The box holds Timken pinion and carrier bearings with races, pinion and carrier shims, a crush sleeve, a nut and seal, ring gear bolts, and the sealer and compounds.

The 35-2029 is built for Chrysler 8.25 inch rear axles with 27 or 29 spline axles, so spline count decides whether this kit is the right one. The master contents are Timken pinion and carrier bearings with races, shims for both, a crush sleeve, a pinion nut and seal, ring gear bolts, thread locker, marking compound and silicone sealer, enough to complete the install.

Key features

  • Master installation kit for the Chrysler 8.25 Inches axle (rear)
  • Includes pinion Nut
  • Includes pinion Seal
  • Includes Timken Outer Pinion Bearing and Race
  • Includes crush Sleeve
  • Includes Timken Inner Pinion Bearing and Race
  • Includes pinion Shims
  • Includes carrier Shims
  • Includes carrier Bearings and Races
  • Includes ring Gear Bolts

Setting pinion depth correctly

Pinion depth and carrier preload are the two settings that decide how long a Chrysler 8.25 inch gear set lasts. Shims control both, so the installer should measure before final assembly rather than trusting an old setup. Bearings that were pressed into worn housings can shift the setting, so inspect the bore and the race seats before you start.

Use a clean bench and keep each shim pack labeled by position. Once the pinion is set, tighten the nut slowly and check the rotational torque against the bearing preload value, then recheck it after the gears have run in. A crush sleeve only collapses once, so do not back the nut off to adjust it.

  • Replace the pinion seal every time the nut is removed
  • Clean ring gear bolt holes before fitting new bolts
  • Keep thread locker away from bearing surfaces

Specifications

Brand G2 Axle and Gear
Part number 35-2029
UPC 631410095777
Kit type Master kit with bearings
Axle location Rear
Axle type Chrysler 8.25 Inches
Axle manufacturer Chrysler

Vehicle fitment

It fits Chrysler 8.25 inch rear axles with 27 or 29 spline axles. Spline count is the key check, so confirm your axle’s spline number before ordering.

Confirm your vehicle’s axle type, spline count and year before ordering.

Installation notes

Count the splines on your axle shafts before ordering, because the kit is matched to 27 or 29 spline units. Then shim the pinion, tighten to the crush sleeve and check the contact pattern.

Before opening the Chrysler 8.25 Inches housing for the 35-2029 job, gather a dial indicator, a torque wrench and clean gear oil. Record the original gear pattern, because the 35-2029 shims are the tool for moving the new pattern toward it. Fit the new nut and seal. Sort shims by thickness.

What’s included

  • Pinion Nut
  • Pinion Seal
  • Timken Outer Pinion Bearing and Race
  • Crush Sleeve
  • Timken Inner Pinion Bearing and Race
  • Pinion Shims
  • Carrier Shims
  • Carrier Bearings and Races
  • Ring Gear Bolts
  • Thread Locking Compound
  • Gear Marking Compound
  • Silicone Sealer

Not included: ring and pinion gears; the 35-2029 supplies installation parts for the Chrysler 8.25 Inches axle only.

SKU: G/235-2029 Category:

Specification

Shipping weight 7.00 lbs
Package dimensions 12.90 × 12.80 × 3.10 in
brands

Questions & Answers

What axle does the 35-2029 kit fit?

It fits the Chrysler 8.25 inch rear axle with 27 or 29 spline axles. Count your axle's spline number before ordering, then confirm the fit for your vehicle's year, model and trim before ordering.

What is included in the 35-2029 kit?

It includes a pinion nut and seal, crush sleeve, Timken inner and outer pinion bearings with races, pinion shims, carrier shims, carrier bearings and races, ring gear bolts, thread locker, marking compound and silicone sealer.

Does the 35-2029 include the gears?

No. Only the installation parts are included; a ring and pinion set is bought separately. Match the 35-2029 to the axle before ordering.

Can I reuse the old crush sleeve or bearings?

No. The crush sleeve deforms when the nut is tightened, so a new one is needed for a proper preload. Bearings and races should also be replaced as a set when the gears are being rebuilt, since worn races can change pinion depth and carrier preload.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon