Overview
The G2 Axle and Gear 4-TJ-488M is a 4.88 ring and pinion gear set with front and rear minor installation kits for the 1997–2006 Jeep Wrangler TJ. The kit pairs a 4.88 front gear set for the Dana 30 front axle with a 4.88 rear gear set for the Dana 35 rear axle, so both axles of the Jeep are regeared in one kit.
The 4-TJ-488M is a complete gear swap kit with front and rear gear sets plus minor installation kits for both axles. It gives Wrangler TJ owners a 4.88 option for changing axle gearing, and its gears are designed for oversized tires and high performance engines.
Key features
- Complete front and rear set: 4.88 ring and pinion gear sets for both axles plus matched minor installation kits
- Built for the Dana 30 front axle and the Dana 35 rear axle
- Computer heat treated 8620 steel gears
- Manufactured to O.E. specifications.
- Double shot peened and double lapped gear sets
- Limited lifetime warranty listed by G2
- Fits non-Rubicon models.
Before you regear
Changing ring and pinion gearing alters how the engine turns the wheels at every speed. A numerically higher ratio, the kind used in this kit, generally improves low-speed pulling and helps offset larger tires, but it also raises engine speed at highway cruising and can affect fuel use. Think about your usual tire diameter and how much trail work you do before committing both axles to new gears.
Regearing usually involves more than the gears themselves. Pinion bearings, carrier bearings, shims, crush sleeves and seals are commonly replaced or reset during a swap, and bearing sets are not part of this kit, so plan to source them separately. Inspect both axle housings and the carrier seats for wear before fitting the new parts.
- Check the tire diameter you plan to run before ordering
- Budget for bearings and seals if the old ones are worn
- Set the gear mesh and tooth contact pattern before the first drive
- Break in new gears gently and recheck fluid level afterward
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 4-TJ-488M |
| UPC | 631410141191 |
| Product type | Ring and pinion gear sets with front and rear minor installation kits |
| Gear ratio | 4.88 |
| Vehicle named in listing | 1997–2006 Jeep Wrangler TJ |
| Front axle | Dana 30 |
| Trim note | Non-Rubicon models |
| Rear axle | Dana 35 |
| Axle location | Front and rear |
| Kit type | Minor kit |
| Gear material | Computer heat treated 8620 steel |
| Finishing | Double shot peened, double lapped |
| Manufacturing | Manufactured to O.E. specs |
| Warranty | Limited lifetime warranty |
Vehicle fitment
It fits the 1997–2006 Jeep Wrangler TJ and is built for a Dana 30 front axle and a Dana 35 rear axle, so the Jeep must have those axles to use this kit. Confirm fit for your vehicle’s year, model and trim before ordering.
The 4-TJ-488M listing does not cover the earlier Wrangler YJ (1987–1995), the Wrangler JK (2007–2018) and other Jeep models. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Fitting the 4-TJ-488M changes the gear ratio on both axles of a Wrangler TJ, which is work for an experienced gear installer. The two minor installation kits in the 4-TJ-488M are the parts used for setting the new gears, and the same 4.88 ratio goes in both axles so the drivetrain stays matched. The 4-TJ-488M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-TJ-488M gears after installation.
What’s included
- Front ring and pinion gear set, 4.88
- Rear ring and pinion gear set, 4.88
- Front minor installation kit
- Rear minor installation kit









