Overview
The G2 Axle and Gear 4-XJ2-456M is a 4.56 ring and pinion gear set with front and rear minor installation kits for the 1990–1996 Jeep Cherokee XJ. The kit pairs a 4.56 front gear set for the Dana 30 reverse front axle with a 4.56 rear gear set for the Dana 35 rear axle, so both axles of the Jeep are regeared in one kit.
For the 4-XJ2-456M, G2 describes its complete ring and pinion kits as including everything needed for a gear swap: front and rear gear sets plus the minor installation kits for both axles. The 4-XJ2-456M gives Cherokee XJ owners a 4.56 option for changing axle gearing, and G2 says its gears are engineered for oversized tires and high performance engines.
Key features
- Complete front and rear set: 4.56 ring and pinion gear sets for both axles plus matched minor installation kits
- Built for the Dana 30 reverse front axle and the Dana 35 rear axle
- Computer heat treated 8620 steel gears
- The gears are made to O.E. specifications.
- Double shot peened and double lapped gear sets
- Limited lifetime warranty listed by G2
- Carrier requirements: front 3.73 and up carrier, rear 3.54 and up carrier.
Matching gears to your axles
Regearing both axles to the same ratio keeps the driveline matched, so each axle turns at similar speeds under load. A gear swap also changes engine rpm at a given road speed, which can affect fuel economy and how the Jeep feels at highway speed. Speedometer and odometer accuracy may change after a ratio change, so check it after the first drives.
Tire size matters just as much. Oversized tires already pull the gearing taller, so the ratio should be chosen with tire diameter in mind. The carrier requirements are part of the same plan, since the carrier must match the gear set for the gears to be used correctly.
- Confirm axle and carrier before ordering
- Use the same ratio front and rear
- Plan setup and break-in with a shop
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 4-XJ2-456M |
| UPC | 631410141368 |
| Product type | Ring and pinion gear sets with front and rear minor installation kits |
| Gear ratio | 4.56 |
| Vehicle named in listing | 1990–1996 Jeep Cherokee XJ |
| Front axle | Dana 30 reverse (3.73 and up carrier) |
| Rear axle | Dana 35 (3.54 and up carrier) |
| Axle location | Front and rear |
| Kit type | Minor kit |
| Gear material | Computer heat treated 8620 steel |
| Finishing | Double shot peened, double lapped |
| Manufacturing | Manufactured to O.E. specs |
| Warranty | Limited lifetime warranty |
Vehicle fitment
It fits the 1990–1996 Jeep Cherokee XJ (90-96 XJ Cherokee). It uses a Dana 30 reverse (3.73 and up carrier) front axle and a Dana 35 (3.54 and up carrier) rear axle, so it applies to a Jeep with those axles.
The 4-XJ2-456M listing does not cover Cherokee XJ model years outside 1990–1996, other Cherokee generations such as the SJ and KL, and the Grand Cherokee. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Fitting the 4-XJ2-456M changes the gear ratio on both axles of a Cherokee XJ, which is work for an experienced gear installer. The two minor installation kits in the 4-XJ2-456M are the parts used for setting the new gears, and the same 4.56 ratio goes in both axles so the drivetrain stays matched. The 4-XJ2-456M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-XJ2-456M gears after installation.
What’s included
- Front ring and pinion gear set, 4.56
- Rear ring and pinion gear set, 4.56
- Front minor installation kit
- Rear minor installation kit






