Overview
The G2 Axle and Gear 4-TJ-410M is a 4.10 ring and pinion gear set with front and rear minor installation kits for the 1997–2006 Jeep Wrangler TJ. The kit pairs a 4.10 front gear set for the Dana 30 front axle with a 4.10 rear gear set for the Dana 35 rear axle, so both axles of the Jeep are regeared in one kit.
The 4-TJ-410M is a complete ring and pinion kit with everything needed for a gear swap: front and rear gear sets plus minor installation kits for both axles. It gives Wrangler TJ owners a 4.10 option for changing axle gearing. The gears are engineered for oversized tires and high performance engines.
Key features
- Complete front and rear set: 4.10 ring and pinion gear sets for both axles plus matched minor installation kits
- Built for the Dana 30 front axle and the Dana 35 rear axle
- Computer heat treated 8620 steel gears
- Manufactured to O.E. specifications.
- Double shot peened and double lapped gear sets
- Limited lifetime warranty listed by G2
- No bearings in the install kit
- Fits non-Rubicon models.
Before the gear swap
Changing axle gearing is a drivetrain job rather than a simple bolt-on swap. A numerically lower ratio keeps engine speed down at highway speed, while a numerically higher ratio gives stronger acceleration and better pulling force from a stop. The right choice depends on tire diameter, transmission gearing and how the Jeep is driven most of the time. Taller tires usually pull the effective ratio down, so a larger tire size often calls for a numerically higher ratio.
Plan for the parts that often get replaced alongside new gears. Carrier and pinion bearings, pinion seals and axle seals wear over time, and a worn pinion seal can leak gear oil onto the brakes. Inspect the existing axle shafts and the differential case for cracks or wear before reassembly. Fresh gear oil, a proper fill level and a gentle break-in period help the new gear teeth seat evenly.
- Check carrier and pinion bearings for play
- Replace hard or leaking seals
- Inspect axle shafts and bearing surfaces
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 4-TJ-410M |
| UPC | 631410141177 |
| Product type | Ring and pinion gear sets with front and rear minor installation kits |
| Gear ratio | 4.10 |
| Vehicle named in listing | 1997–2006 Jeep Wrangler TJ |
| Front axle | Dana 30 |
| Trim note | Non-Rubicon models |
| Rear axle | Dana 35 |
| Axle location | Front and rear |
| Kit type | Minor kit |
| Gear material | Computer heat treated 8620 steel |
| Finishing | Double shot peened, double lapped |
| Manufacturing | Manufactured to O.E. specs |
| Warranty | Limited lifetime warranty |
| Bearings | No bearing in install kit |
Vehicle fitment
It fits the 1997–2006 Jeep Wrangler TJ, and it is made for a Jeep with a Dana 30 front axle and a Dana 35 rear axle.
The 4-TJ-410M listing does not cover the earlier Wrangler YJ (1987–1995), the Wrangler JK (2007–2018) and other Jeep models. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Fitting the 4-TJ-410M changes the gear ratio on both axles of a Wrangler TJ, which is work for an experienced gear installer. The two minor installation kits are used for setting the new gears, and the same 4.10 ratio goes in both axles so the drivetrain stays matched. No bearings come in the install kit, so source bearing replacements separately. Plan a careful break-in for the new gears after installation.
What’s included
- Front ring and pinion gear set, 4.10
- Rear ring and pinion gear set, 4.10
- Front minor installation kit
- Rear minor installation kit
Not included: bearings (the install kit does not include any).







