Overview
The Dana Spicer 660182-5 is a Dana 60 front passenger side inner axle shaft, 17.67 inches long with 35 splines, for 1977–1991 GM 1 ton trucks. Dana Spicer calls its replacement axle shafts the shafts that came in the vehicle from the factory. The 660182-5 is the inner piece for the passenger side of the front axle and accepts the 5-806X u-joint.
Micro-alloy material is used for strength, and a controlled heat treatment sets the hardness. The fit covers a wide run of Chevrolet and GMC trucks, Blazers, Jimmys and Suburbans.
Key features
- Front passenger side inner axle shaft
- Dana 60 front axle
- 35 splines
- 17.67 inches overall length
- Accepts the 5-806X u-joint
- Micro-alloy material.
- Controlled heat treatment.
Checking the inner shaft
The inner shaft carries power from the front differential out toward the hub, so it works under constant torque and articulation. Wear usually shows at the splines, where the shaft meets the gears, and at the u-joint where it connects to the axle.
Start with a visual check of the boot or seal area for grease loss, then look for play or clicking when the wheels are turned. A shaft that twists or shows a bent section should be replaced rather than straightened.
When the shaft is out, inspect the splines on both ends for rounding and check the u-joint movement by hand. Replacing a worn u-joint at the same time is a sensible step, since it is cheap compared with another job later.
- Check spline wear on both ends
- Look for grease leaks around the seal
- Replace a bent shaft
Specifications
| Brand | Dana Spicer |
|---|---|
| Part number | 660182-5 |
| Axle manufacturer | Dana |
| Axle position | Front |
| Shaft location | Passenger Side Inner |
| Axle type | Dana 60 |
| Position | Front Right Inner |
| Spline count | 35 Splines |
| Overall length | 17.67 inches |
| Material | Micro-alloy |
| Accepts | 5-806X u-joint |
| Applications noted | 77-91 GM 1 ton trucks |
Vehicle fitment
The fitment below covers the trim levels shown for each vehicle.
- 1987–1991 Chevrolet Blazer (Custom Deluxe, Scottsdale, Silverado)
- 1984–1986 Chevrolet K10 (Custom, Scottsdale, Silverado)
- 1984–1986 Chevrolet K10 Suburban (Custom, Scottsdale, Silverado)
- 1984–1986 Chevrolet K20 (Custom, Scottsdale, Silverado)
- 1984–1986 Chevrolet K20 Suburban (Custom, Scottsdale, Silverado)
- 1984–1986 Chevrolet K30 (Custom, Scottsdale, Silverado)
- 1984–1986 Chevrolet K5 Blazer (Custom, Scottsdale, Silverado)
- 1987 Chevrolet V10 (Custom Deluxe, Scottsdale, Silverado)
- 1987–1988 Chevrolet V10 Suburban (Custom Deluxe, Scottsdale, Silverado)
- 1989–1991 Chevrolet V1500 Suburban (Scottsdale, Silverado)
- 1987 Chevrolet V20 (Custom Deluxe, Scottsdale, Silverado)
- 1987–1988 Chevrolet V20 Suburban (Custom Deluxe, Scottsdale, Silverado)
- 1989–1991 Chevrolet V2500 Suburban (Scottsdale, Silverado)
- 1987–1988 Chevrolet V30 (Cheyenne, Custom Deluxe, Scottsdale, Silverado)
- 1989–1991 Chevrolet V3500 (Cheyenne, Scottsdale, Silverado)
- 1984–1991 GMC Jimmy (Base, High Sierra, Sierra Classic)
- 1984–1986 GMC K1500 (Base, High Sierra, Sierra Classic)
- 1984–1986 GMC K1500 Suburban (Base, High Sierra, Sierra Classic)
- 1984–1986 GMC K2500 (Base, High Sierra, Sierra Classic)
- 1984–1986 GMC K2500 Suburban (Base, High Sierra, Sierra Classic)
- 1984–1986 GMC K3500 (Base, High Sierra, Sierra Classic)
- 1987 GMC V1500 (Base, High Sierra, Sierra Classic)
- 1987–1991 GMC V1500 Suburban (Base, High Sierra, SLE, Sierra Classic)
- 1987 GMC V2500 (Base, High Sierra, Sierra Classic)
- 1987–1991 GMC V2500 Suburban (Base, High Sierra, SLE, Sierra Classic)
- 1987–1991 GMC V3500 (Base, High Sierra, SLE, Sierra Classic)
The vehicles and years above are the ones covered. Other GM trucks and other front axle sizes need different shafts. Confirm your vehicle’s year, model and trim before ordering.





