Overview
The Baer Brakes 4262669C is a dual Deep Stage rear brake kit with clear powder coated S4 calipers, made for Ford 8.8 inch rear ends that use C-clip eliminators.
Baer positions the SS4 Plus Dual Deep Stage as a drag race system for heavy, fast cars that may also be driven on the street. Four calipers clamp 11 inch rotors, and the kit is built for wheels of 15 inch and up.
Key features
- Four two-piece S4 calipers carry 1.75 inch pistons and are manufactured in Phoenix, Az
- Clear powder coat finish on the calipers
- Noise suppression clips and stainless steel abutments sit alongside hard anodized aluminum pistons
- Two-piece rotor, slotted, drilled and zinc plated, at 11 inch outside diameter
- Billet aluminum hats, drilled to take 5/8 inch wheel studs
- Dust and weather seals
- DR1 or HB100 pad type
- Pre-assembled rotors use NAS high grade stainless hardware
Choosing a rear brake setup
A dual caliper drag brake kit changes how the rear axle stops a heavy car, so the rest of the braking system needs to be considered alongside it. Heavier braking loads place more demand on the master cylinder, brake lines and front brakes, and a balanced setup helps the car stop predictably. Drivers who run the kit on the street should expect firmer pedal feel and more heat than a stock rear brake, which is normal for a larger, performance-oriented system.
Clear powder coated calipers stay visible through the wheel, so the finish is mainly a styling choice. The pistons and stainless abutments are the parts that affect how the calipers move and hold, so keeping them clean and free of corrosion supports consistent operation. Seals should be checked whenever the calipers are removed for pad service.
- Check master cylinder size and front brake capacity before adding rear clamping force
- Use fresh brake fluid rated for high-temperature use
- Inspect dust and weather seals each time pads are changed
- Keep rotor hardware tight after any removal
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262669C |
| UPC | 844165049043 |
| Sold as | Kit |
| Caliper | S4, four-piston, fixed, two-piece, clear powder coat |
| Caliper quantity | 4 |
| Piston size | 1.75 inch |
| Rotor outside diameter | 11.0 inch |
| Rotor type | Two-piece, vented, slotted, drilled and zinc plated |
| Rotor material | Iron with aluminum hat |
| Rotor thickness | 1.02 |
| Pad type | DR1 or HB100 (FMSI DR1) |
| Friction material | Semi-metallic |
| Grade | Performance |
| Axle flange | Ford 8.8 inch, C-clip eliminator |
| Axle flange requirement | 5.75 inch |
| Axle standoff | 2.5 inch |
| Wheel bolt pattern | 5 lug, 5×4.50/5×4.75 |
| Minimum wheel diameter | 15.0 inch |
| Park brake | No |
| Brake hoses included | No |
| Lug nuts included | No |
| Country of origin | US |
Vehicle fitment
No specific vehicle is named for this kit. Its application is a Ford 8.8 inch rear axle with C-clip eliminators, a 5×4.50/5×4.75 bolt pattern and a 5.75 inch axle flange.
Axles that still carry a standard C-clip fall outside this kit’s application. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Rotor hardware arrives assembled and mounting hardware is included. The kit does not work with a standard C-clip, so eliminator-equipped axles must be in place. Given the drag race purpose, check the setup before any hard use.
What’s included
Four S4 calipers, pre-assembled rotors with stainless hardware, and the mounting hardware.
Not included: a park brake, brake hoses, a front rotor and lug nuts.















