Overview
The Baer Brakes Big Claw front brake rotor kit, part number 2261046, is an oversized replacement rotor set for the 2021–2026 Ford F-150, including the F-150 Raptor. Each rotor is up to 2 inches larger in diameter than stock on some applications and is cast with directional cooling vanes.
A pair of brackets moves each caliper outward so the larger rotors clear, and the kit keeps OE pad and hardware use. Independent third-party testing shows up to a 49 percent gain in braking effectiveness from the added torque and leverage, and as much as a 200-degree reduction in rotor temperature versus OE in extreme conditions, partly due to the curved vane design.
Key features
- One-piece, full cast rotors that deliver greater brake torque and leverage
- Slotted and cross-drilled friction surface to help vent dust and gases for a steadier pedal feel
- Purpose-cast directional vanes that move air through the rotor to reduce brake fade
- Caliper relocation brackets that keep OE pad and hardware compatibility
- Direct bolt-on system with no brake bleeding required
- Zinc plated finish that resists rust and corrosion behind open-spoke wheels
Choosing the right setup
Oversized rotors change more than stopping force. A larger diameter adds leverage at the caliper, so the pedal may feel firmer under load, but the rest of the braking system has to keep up. Check the master cylinder, brake lines and pads for good condition before relying on a larger rotor with a loaded truck or on a steep grade.
Front rotors are often replaced together with pads. New pads bed in against new rotors, so plan a break-in run at moderate speed before heavy use. Check hub torque after the first few drives and re-tighten the wheel lug nuts once the wheels have settled.
Warning signs of a worn rotor include pulsation through the pedal, grooves that catch a fingernail, and a thickness at or below the discard thickness. Inspect the braking surface whenever the wheels come off, especially after off-road use, when mud and grit wear the surface faster.
- Replace pads and rotors as a matched set when wear is uneven
- Clean hub faces and mating surfaces before mounting
- Re-check lug torque after the first few drives
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 2261046 |
| UPC | 90127866214 |
| Sold as | Set |
| Country of origin | USA |
| Axle | Front |
| Drive | 2WD, 4WD |
| Construction | One piece, full cast |
| Rotor type | Conventional, vented, floating |
| Surface type | Slotted X Drilled |
| Vent type design | Curved |
| Directional brake surface | Directional |
| Material | Cast iron |
| Disc finish | Zinc plated, rust resistant coating |
| Outside diameter | 15 |
| Nominal thickness | 1.181 |
| Discard thickness | 1.102 |
| Overall height | 2.126 |
| Center hole diameter | 3.547 |
| Mounting bolt hole quantity | 5 |
| Mounting bolt hole diameter | 0.625 |
| Mounting bolt hole circle diameter | 5.31 |
| Stud/lug hole quantity | 6 |
| ABS tone ring included | No |
| Warranty | Limited 1 Year Warranty |
Vehicle fitment
The kit fits the 2021–2026 Ford F-150 front axle, covering Performance Upgrade units with RWD and 4WD drive. The rotors do not fit OE Raptor wheels, so check wheel clearance with the template for this system before ordering.
The 2010–2020 Ford F-150 uses a different Baer front rotor kit, part 2261043, and is not covered here. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
This is a direct bolt-on swap at the front hubs, and the brakes do not need bleeding. Baer cannot guarantee fit into every aftermarket wheel, so use the template for this system and compare it with your wheel of choice, including the spare tire and wheel. Because the brackets move the calipers outward, check caliper clearance inside the wheel before final assembly.
Test pedal feel at low speed in an open area before returning to normal driving.
What’s included
The kit includes a pair of oversized rotors and a pair of caliper relocation brackets.

















