Select your vehicle
-13%

Alloy USA Ford 8.8 Rear Axle Shaft – 15104

Alloy USA

Shop Ford F-150 Replacement Axle Shafts on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Ford 8.8 rear axle shaft, 31 spline, driver side
  • For 1987-1996 Ford F-150 and Bronco
  • Does not include bearings, seals or studs

Description

Overview

The Alloy USA 15104 is a Ford 8.8 rear axle shaft for the driver side, with 31 splines. It fits 1987-1996 Ford F-150 and Bronco models.

Each shaft is heat treated and induction hardened, and the line is made from 1541H or 4140 steel. The shaft is designed for twice the tensile strength of a stock shaft. The 31 splines must match the differential or carrier. This is a driver side shaft, so a vehicle needing both rear shafts will also need a passenger side shaft.

Key features

  • Replacement shaft for the Ford 8.8 rear axle
  • 31 spline
  • Driver side
  • Fits the 1987-1996 F-150 and Bronco.
  • Alloy USA says its shafts are heat treated and induction hardened
  • Bearings, seals and studs are not included
  • Axle: Ford 8.8 inch rear
  • Axle shaft location: Driver side (rear left)

Driver side replacement tips

The driver side shaft carries the same load as the passenger side, but it sits near the brake lines and the differential cover, so take care not to bend lines during removal. Clean the flange and the axle tube before the new shaft goes in, and inspect the old shaft’s splines while it is still out for comparison.

A shaft that is replaced alone should match the spline count and length of the other side as closely as possible. Mismatched shafts can cause uneven wear and a difference in traction. Driver and passenger shafts are separate parts, so both sides should be checked for condition before reassembly, especially on older vehicles that have seen rough use.

  • Note the shaft side before removing either shaft
  • Inspect the brake lines for kinks after the swap
  • Re-check the wheel studs after the first drive
  • Keep the removed shaft as a reference

Specifications

The 15104 is a replacement axle shaft for the Ford 8.8 inch rear axle, with 31 splines. Every figure in the table below is the manufacturer value for the 15104.

Brand Alloy USA
Part number 15104
UPC 80177304395
Part type Replacement axle shaft
Axle Ford 8.8 inch rear
Axle shaft location Driver side (rear left)
Spline 31 spline
Manufacturer part number ALY15104
Application stated 87-96 Ford F-150 and Bronco

Vehicle fitment

It is for 87-96 Ford F-150 and Bronco models, meaning the 1987-1996 F-150 and 1987-1996 Bronco. Measure the shaft you are replacing and compare spline count, length and side before ordering.

It is for use in 87-96 Ford F-150 and Bronco models.

Measure the shaft you are replacing and compare it with the 15104 listing for spline count, length and side.

Confirm your vehicle’s year, model and trim before ordering.

Installation notes

None of the bearings, seals or studs are included with the 15104, so check the condition of the old ones during the swap.

What’s included

One axle shaft.

Not included: Bearings, Seals, Studs.

SKU: ALY15104 Category:

Specification

Shipping weight 22.00 lbs
Package dimensions 37.50 × 7.00 × 7.00 in
brands

Fitment

VehicleYearsTrims
Ford Bronco likely fits1987–1996All
Ford F-150 likely fits1987–1996All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Which Fords does the Alloy USA 15104 fit?

It is for 87-96 Ford F-150 and Bronco models. It is a Ford 8.8 inch rear axle shaft for the driver side.

How many splines is the Alloy USA 15104?

The 15104 has 31 splines. It is a replacement shaft for the Ford 8.8 inch rear axle, driver side, and Alloy USA gives no length.

Does the Alloy USA 15104 include bearings and studs?

No. Bearings, seals and studs are not included with the 15104 shaft, so check the condition of the old ones during the swap.

Is it necessary to match the driver and passenger shafts?

They should match in spline count and length, since both shafts connect to the same gear set. A mismatch can cause uneven traction and wear, so compare the old shaft before ordering. Keep the removed shaft as a reference during the job.

How should a driver side shaft be stored before installation?

Keep it flat and clean, with the splines protected from dirt and impact. Store it indoors if possible, and check the bearing surface for rust before fitting. Avoid standing it on the flange where it can bend.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Ford F-150 Replacement Axle Shafts on Amazon