CJ Clutch Parts
Showing 61–72 of 77 resultsSorted by popularity
The CJ mechanical clutch linkage
Through 1986, Jeep CJs released the clutch with rods and levers rather than fluid. The pedal arm pushes a pedal rod down to a bellcrank, a bent lever that pivots on a pair of ball studs, one on the frame rail and one on the engine block, and the far end of the bellcrank pushes a second rod into the clutch fork. Because the engine rocks on its mounts while the frame does not, the bellcrank rides on bushings that take up the movement, and those bushings are the weak point. When they wear, the lever flops, pedal travel is wasted and the clutch never fully releases, which feels like a clutch that is going out even when the disc is fine.
The parts here map directly onto that system: pedal rods for four cylinder flathead and F-head CJs, bellcrank levers for 1976 to 1986 CJ5, CJ7 and Scrambler, and the pivot balls and fulcrums that the fork rides on. Note that many bellcrank levers are sold without bushings and clips, so add the bushing kit.
Release bearings by engine
The release bearing, or throwout bearing, must match the engine and bellhousing. In this category you will find bearings for the AMC 232 and 258 inline sixes and the 304 to 401 V8s of 1972 to 1975, a different bearing for 1980 to 1986 CJs with the GM 2.5L four, the 4.2L 258 six, the 304 and 360 V8s and the Renault 2.1 diesel, and later bearings for the 2.8L and 3.8L engines in the XJ, KJ and Wrangler. A CJ built in 1979 and one built in 1981 can take different bearings even with the same engine, so use the year and engine together.
Hydraulic parts for later Jeeps
From the mid 1980s Jeep adopted hydraulic release, and because this category also catalogs master cylinders, slave cylinders and flywheels for the Cherokee XJ, Comanche and Wrangler YJ and TJ, it is worth knowing the layout. The master cylinder bolts to the firewall and is fed by a small reservoir. The slave cylinder is either an external unit on the bellhousing or a concentric unit inside it on the AX15 and BA 10/5 transmissions, where the slave cylinder and bearing are one assembly. Buying both a bearing and a concentric slave for an AX15 would duplicate the part.
- Master cylinders for 1987 to 1990 XJ and for 1991 to 1996 XJ and Comanche are different parts; watch the year split.
- Some hydraulic assemblies are sold complete with master, hose and slave, prefilled, which eliminates bleeding. Confirm left-hand drive and the engine named in the listing.
- Flywheels for the 2.5L four cover XJ, YJ and TJ with a standard transmission; the 4.0L uses a different flywheel.
Adjusting and setting free play
After replacing any linkage part on a mechanical CJ, set free play at the fork rod so the bearing sits just off the pressure plate fingers at rest, typically about an inch of pedal travel before resistance. Too little free play keeps the bearing spinning under load and kills it; too much means the clutch drags and the transmission grinds going into first. Grease the ball studs and bellcrank bushings, and check that the engine mounts are not collapsed, because a sagging engine changes the bellcrank angle and the adjustment with it.
Installation reminders
Pulling the transmission on a CJ is straightforward but heavy; use a jack and support the engine when the rear mount comes out. Replace the pilot bushing while you are there. On hydraulic Jeeps use fresh DOT 3 brake fluid and bleed at the slave until no air appears. A clutch that still feels wrong after new parts often traces back to a worn pedal pivot bushing up under the dash, which is cheap and easy to overlook.
Popular CJ Clutch Parts brands
CJ Clutch Parts FAQ
Why will my CJ clutch not fully disengage after a new clutch?
On a mechanical linkage CJ the usual cause is worn bellcrank bushings or ball studs, which absorb pedal travel before the fork moves. Replace the bushings, grease the pivots, check the engine mounts and reset free play at the fork rod. A bent pedal rod has the same effect.
Which release bearing fits my CJ?
It depends on year and engine together. Bearings differ between the 1972 to 1975 AMC six and V8 engines, the 1980 to 1986 CJs with the 2.5L four, 258 six and V8s, and later Jeep engines. Confirm both before choosing, and compare the old bearing's collar diameter.
Does a bellcrank lever come with bushings?
Usually not. Omix-Ada and Crown bellcrank levers are typically sold bare, without the bushings and clips that wear out first. Order the bushing and clip kit at the same time so the job is done in one pass.
Can I convert a CJ to a hydraulic clutch?
Conversion kits exist from other makers, but the parts here are direct replacements for the factory systems: linkage for CJs through 1986 and hydraulic parts for the XJ, YJ and TJ. If you keep the mechanical linkage in good condition it works well and is simple to adjust.











