Overview
The Poison Spyder Customs 11-20-010 is a full width axle conversion kit of bare steel brackets for the Jeep CJ5, CJ7 and Scrambler. It moves the front spring perches outboard with a bolt-on bracket and relocates the rear shackle hangers with a weld-on bracket, and it builds in a shackle reversal.
The front bracket also moves the front axle 1 inch forward of the stock position, which helps tire clearance as the axle rotates rearward under compression. The kit is designed for 2-1/2 inch wide leaf springs. Narrower springs can be used with spacers, which are not included.
The rear weld-on bracket offers 10 different shackle hanger mounting positions, which allows spring lengths from stock up to 5 inch longer than stock, and the multiple points allow adjustment for longer shackles.
Key features
- Bolt-on front outboard bracket
- Weld-on rear bracket with 10 shackle hanger positions
- Shackle reversal for extra lift
- Moves the front axle 1 inch forward of stock
- Designed for 2-1/2 inch wide leaf springs
- Supports springs up to 5 inch longer than stock
- Bare steel finish
Springs, shackles and driveline
Spring width drives how this kit goes together. The kit is built around 2-1/2 inch wide leaf springs, so any narrower pack needs spacers to center it on the bracket. Shackle reversal changes the geometry of the rear end, so plan the shackle length before welding anything. Buy shackles, spacers and springs as a set so the lengths and eye sizes match the rear bracket position you choose.
Changing axle position and spring length affects the driveline, brake lines and steering. Check the pinion angle and driveshaft U-joints after the install, and look for binding at full droop. Make sure the brake lines and any sensor wires have enough length to reach their new positions without rubbing. Recheck all bolts and welds after the first longer drives.
- Shackles sized for the chosen hanger position
- Spacers for springs narrower than 2-1/2 inch
- Brake line and wire length check after the axle moves
Specifications
| Brand | Poison Spyder Customs |
|---|---|
| Part number | 11-20-010 |
| UPC | 614901723625 |
| _pn | 11-20-010 |
| Finish | Bare steel |
| Front bracket | Bolt-on, outboard |
| Rear bracket | Weld-on |
| Rear shackle hanger positions | 10 |
| Front axle shift | 1 inch forward |
| Designed for spring width | 2-1/2 inch |
| Spring length | Stock to 5 inch longer than stock |
| Shackles | Not included |
Measure your planned lift and check the total kit weight against your suspension plan before installing.
Vehicle fitment
The kit fits the Jeep CJ5 from 1976 to 1983, the CJ7 from 1976 to 1986 and the Scrambler from 1981 to 1985. It is a direct fit for those models.
The manufacturer fitment list for part 11-20-010 covers: 1976–1983 Jeep CJ5; 1976–1986 Jeep CJ7; 1981–1985 Jeep Scrambler.
Not listed: the CJ5 before 1976 or after 1983, the CJ7 outside 1976-1986, and the Wrangler (YJ and later). Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Welding is needed for the rear bracket, which is welded to the chassis, while the front bracket bolts on. Springs narrower than 2-1/2 inch need spacers, which are not included. Check alignment and driveline angles after the spring and axle geometry changes.
What’s included
- Front outboard bracket (bolt-on)
- Rear shackle hanger bracket (weld-on)
Not included: shackles, the spacers needed for narrower springs, the leaf springs themselves, and the axle.









