Select your vehicle
-13%

Poison Spyder Rear DeFender Flares (Bare Steel) – 14-05-B75

Poison Spyder Customs

Shop Jeep Wrangler TJ Tube Fenders on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rear bolt-on DeFender flares, 5 inch wide, bare steel, part 14-05-B75
  • Formed from 3/16 inch steel plate
  • Bolt-on application with cutting or drilling
  • Can be added to Crusher Corners or competitor full corner armor

Description

Overview

The Poison Spyder 14-05-B75 is a rear bolt-on DeFender flare, 5 inch wide, finished in bare steel. It is designed to match Poison Spyder’s front DeFenders and can be added to an existing set of Crusher Corners.

The flare can also be added to a competitor’s full corner armor. It is fabricated entirely from 3/16 inch plate with a sturdy outer edge and a full under-side return for strength.

Installation is cutting or drilling, so the mounting holes need planning before the flare is fitted. It fits several CJ, Wrangler LJ, TJ and YJ models.

Key features

  • 5 inch wide rear flare
  • Bolt-on application
  • Fabricated entirely from 3/16 inch plate
  • Full under-side return on the outer edge
  • Can be added to existing Crusher Corners

Planning the mounting holes

A bolt-on flare still depends on careful layout. The holes decide how the flare sits against the corner, so hold the part in position and mark the drill points with it in place. Measure the clearance to the tire and body at full steering lock before drilling, since a hole in the wrong spot is difficult to correct.

Bare steel cut edges and drilled holes are open to moisture, so deburr them and treat them with a rust-inhibiting primer before the bolts go in. Recheck the fasteners after the first few trail runs, as flexing can loosen them. Keep a note of the hardware sizes used in case replacements are needed later.

  • Mark drill points with the flare held in place
  • Check tire and body clearance at full steering lock
  • Deburr cut edges and holes before fastening
  • Prime exposed bare steel to slow rust

Specifications

Brand Poison Spyder Customs
Part number 14-05-B75
UPC 614901736267
Position Rear
Flare width 5 inch
Material 3/16 inch plate steel
Finish Bare steel
Application Bolt-on
Installation Cutting or drilling required

Vehicle fitment

It fits the 1976–1983 Jeep CJ5, the 1976–1986 Jeep CJ7, the 2004–2006 Jeep Wrangler LJ, the 1997–2006 Jeep Wrangler TJ, and the 1987–1995 Jeep Wrangler YJ, across the trim lines for each model.

The list covers several generations, so confirm your vehicle’s year, model and trim before ordering.

Installation notes

Cutting or drilling is required, so plan the mounting holes before the flare is set in place. The flare is a bolt-on part and does not require welding.

What’s included

One rear bolt-on DeFender flare in bare steel.

SKU: PSC14-05-B75 Category:

Specification

Shipping weight 64.00 lbs
Package dimensions 46.00 × 19.00 × 13.00 in
brands

Fitment

VehicleYearsTrims
Jeep CJ51976–1983Base, Golden Eagle, Laredo, Limited, Renegade
Jeep CJ71976–1986Base, Golden Eagle, Golden Hawk, Laredo, Limited, Renegade
Jeep Wrangler (LJ)2004–2006Unlimited, Unlimited Rubicon
Jeep Wrangler (TJ)1997–200665th Anniversary Edition, Rubicon, SE, Sahara, Sport, X
Jeep Wrangler (YJ)1987–1995Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara, Sport

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Is this 5 inch flare a bolt-on part?

Yes. The application is bolt-on, and the installation type is cutting or drilling, so holes must be planned before the flare is mounted.

Which Jeeps are listed?

It fits the CJ5, CJ7, Wrangler LJ, TJ and YJ models, across the trim lines for each one. Check the year and trim before ordering.

Can it be added to existing corners?

Yes. The flare can be added to an existing set of Poison Spyder Crusher Corners or to a competitor's full corner armor.

Do bolt-on flares need touch-up after mounting?

Often yes. Bare steel cut edges and drilled holes can rust if left exposed, so clean and prime them after fitting. Check the mounting bolts after the first few trail runs and retighten them as needed.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wrangler TJ Tube Fenders on Amazon