Select your vehicle
-13%

G2 Rear Dana 44 Axle Truss System – 68-2052

G2 Axle and Gear

Shop Jeep Wrangler JK Axle Truss on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • G2 rear Dana 44 axle truss and armor system, part 68-2052
  • Heavy-duty steel, 1/4 inch main components and 1/8 inch reinforcement plates
  • Covers the whole axle, not just the long tube
  • Includes coil buckets and the main axle truss assembly
  • Welding required; unpainted

Description

Overview

The G2 Rear Dana 44 Axle Truss System, part 68-2052, is a heavy-duty steel truss and armor system for the rear Dana 44 axle of a Jeep Wrangler JK, 2007 to 2018. It is built for the two-door and four-door JK.

The design strengthens the whole axle, not just the long tube. The truss adds support across the axle housing, which helps owners running heavy loads or larger tires.

The main components are 1/4 inch thick steel and the reinforcement plates are 1/8 inch thick. Every piece is laser cut for a fit G2 describes as precise, which keeps the installation straightforward once the parts are welded in place.

Welding is required, including to the cast center section. The manufacturer strongly recommends professional welding skills for this job. The system is supplied unpainted, so paint or coating is up to the installer.

The kit includes the coil buckets and the main axle truss assembly. The upper link mount is sold separately under part number G/268-2052-2, and this version is set up without a steering ram mount.

Key features

  • Heavy-duty steel construction
  • 1/4 inch thick main components
  • 1/8 inch thick reinforcement plates
  • Laser cut to fit
  • Strengthens the full axle, not only the long tube
  • Includes coil buckets and the main axle truss assembly
  • Unpainted, for welding in place

Before welding the truss

A truss like this spreads load across the axle housing, so forces from rough trail running and heavy tires are shared rather than concentrated at one tube. Because the main pieces are cut to fit, the work is mostly about placing them correctly and welding each joint in a planned order. Heat from welding can move thin sections, so tack the pieces, check alignment against the axle, and only then complete the full welds.

Before you start, look over the axle, brake lines, driveline and the cast center section for wear or damage. A cracked housing or worn bearing should be addressed before adding a truss, because the new structure will not correct an existing fault. Once welded, the unpainted steel will need paint or coating to resist rust, and recoating welded areas after the first season is a practical habit.

Specifications

Brand G2 Axle and Gear
Part number 68-2052
UPC 70000702979
Axle Rear Dana 44
Fitment Direct fit; without steering ram mount
Material Heavy-duty steel; 1/4 inch main components, 1/8 inch reinforcement plates
Finish Unpainted
Upper link mount Sold separately, part G/268-2052-2

Vehicle fitment

The truss is for the Jeep Wrangler JK, 2007 to 2018, with a rear Dana 44 axle, in two-door and four-door models.

The Wrangler JL (2018 and later), the earlier TJ and LJ generations and the Gladiator are not covered by this truss.

Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Welding is required, including to the cast center section, and professional welding skills are strongly recommended. Plan the weld sequence and fit-up before cutting into the vehicle.

What’s included

The coil buckets and the main axle truss assembly.

Not included: the upper link mount, sold separately as part G/268-2052-2.

SKU: G/268-2052 Category:

Specification

Shipping weight 34.00 lbs
Package dimensions 29.00 × 12.00 × 9.00 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (JK) likely fits2007–2018All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the G2 68-2052 truss fit a Jeep Wrangler JK with a Dana 44 rear axle?

Yes. It fits the Jeep Wrangler JK, 2007 to 2018, with a rear Dana 44 axle, as a direct fit without a steering ram mount.

Does the G2 rear truss need welding?

Yes. Welding is required, including to the cast center section, and professional welding skills are strongly recommended. Plan the weld sequence and fit-up before cutting into the vehicle.

What comes in the kit, and what is sold separately?

The kit includes coil buckets and the main axle truss assembly. The upper link mount is sold separately under part number G/268-2052-2.

Should the axle be checked before adding a truss?

Yes. Inspect the housing, bearings, brake lines and driveline first, since a truss strengthens the axle but does not repair existing wear or damage. Address any faults before welding so the new structure is installed on a sound axle.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wrangler JK Axle Truss on Amazon