Select your vehicle

G2 Dana 35 YJ/XJ C-Clip 30 Spline Rear Chromoly Axle Kit – 96-2049-2-30

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Dana 35 C-clip rear chromoly axle kit, 30 spline, 5-lug dual drilled 5×4.5/5.5
  • For 1991 and newer Jeep Wrangler (YJ), Cherokee (XJ) and Wrangler (TJ)
  • Includes wheel bearings, seals and screw-in wheel studs; for use with a 30 spline differential

Description

Overview

The G2 Axle and Gear 96-2049-2-30 is a Dana 35 C-clip rear chromoly axle kit with 30 splines and a dual-drilled 5×4.5/5.5 5-lug pattern. It is for 1991 and newer Jeep Wrangler (YJ), Cherokee (XJ) and Wrangler (TJ) models.

G2 Axle and Gear says its axle kits are made from high-tensile alloy steels that are forged and heat treated for strength, and that the larger diameter of Big Spline shafts lets them withstand much higher torsional loads than the stock diameter, so the axle shafts stop being the weakest point of the driveline. Spline count matters: the 30 splines on the 96-2049-2-30 have to agree with the gear set inside the axle.

Key features

  • Rear axle kit for the Dana 35 C-clip axle
  • 30 spline, for use with a 30 spline aftermarket differential
  • 5-lug dual drilled 5×4.5/5.5 pattern
  • Includes wheel bearings and seals
  • Includes screw-in wheel studs
  • Made from high tensile alloy steel, forged and heat treated.

Matching the differential

Axle shafts and the differential engage through splines, so the spline count of the shaft and the gear set inside the axle must agree. Before buying, confirm the differential you are running and count its splines. A mismatch will not seat properly, and the shaft will not carry load as designed.

Replacing one shaft often means checking the other side as well. Look at the bearings, seals and wheel studs on both sides, since worn parts on the opposite side can be replaced during the same job. Clean the axle housing and check the bearing bore for damage before the new components go in.

  • Count the splines on the differential before ordering
  • Compare shaft length with the old shaft
  • Inspect the opposite side while the axle is apart

Specifications

The 96-2049-2-30 is a rear axle kit for the Dana 35 C-clip rear axle, with 30 splines. Every figure in the table below is the manufacturer value for the 96-2049-2-30.

Brand G2 Axle and Gear
Part number 96-2049-2-30
UPC 631410096927
Part type Rear axle kit
Axle Dana 35 C-clip rear
Spline 30 spline
Lug pattern 5-lug dual drilled 5×4.5/5.5
Differential For use with a 30 spline aftermarket differential (none included)
Application stated 91-UP YJ/XJ/TJ

Vehicle fitment

The kit is for 91-UP YJ, XJ and TJ models. By chassis code, that covers the 1991-1995 Wrangler (YJ), the 1991-2001 Cherokee (XJ) and the 1997-2006 Wrangler (TJ).

The application for the 96-2049-2-30 is 91-UP YJ/XJ/TJ.

Match the 96-2049-2-30 against your old shaft for spline count, length and driver or passenger side before installing it.

Confirm your vehicle’s year, model and trim before ordering, particularly if it is an LJ, JK or JL.

Installation notes

The kit is for use with a 30 spline aftermarket differential, so the differential must be 30 spline. It is a C-clip axle kit with a dual-drilled 5-lug pattern; G2 lists wheel bearings, seals and screw-in wheel studs as included.

What’s included

  • Wheel bearings
  • Seals
  • Screw-in wheel studs
  • Axle shafts

Not included: 30 spline aftermarket differential.

SKU: G/296-2049-2-30 Category:

Specification

Shipping weight 40.55 lbs
Package dimensions 39.00 × 8.00 × 8.00 in
brands

Fitment

VehicleYearsTrims
Jeep Cherokee (XJ) likely fits1991–2001All
Jeep Wrangler (TJ) likely fits1997–2006All
Jeep Wrangler (YJ) likely fits1991–1995All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What Jeeps does the G2 96-2049-2-30 fit?

The kit is for 91-UP Wrangler (YJ), Cherokee (XJ) and Wrangler (TJ) models. By chassis code that is the 1991-1995 Wrangler (YJ), the 1991-2001 Cherokee (XJ) and the 1997-2006 Wrangler (TJ).

What comes with the G2 96-2049-2-30 kit?

The kit includes wheel bearings, seals and screw-in wheel studs along with the axle shafts. It does not include the differential, which must be a 30 spline aftermarket unit.

Is the 96-2049-2-30 a C-clip axle kit?

Yes. It is a Dana 35 C-clip rear axle kit with 30 splines and a 5-lug dual-drilled 5x4.5/5.5 pattern. Match the spline count to your differential before ordering.

How can you tell an axle shaft needs replacing?

Common signs include a clicking or popping noise when turning, grease leaking past the seal, vibration under acceleration, and a shaft that has twisted or cracked near the splines. Lift and support the vehicle safely, then inspect the seal and shaft before deciding.

Should the bearings be replaced along with the axle shaft?

Usually yes. Replacing the bearings and seals alongside the shaft keeps the axle assembly sound and avoids a second tear-down. Check the old bearings for play and roughness first, since that shows whether they are ready to be reused.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon