Overview
The G2 Axle and Gear 97-2031-004 is a Dana 30 chromoly inner axle shaft for the driver side, with 30 splines and a 16.50 inch overall length. It fits 1987-2006 Jeep Cherokee (XJ), Wrangler (YJ) and Wrangler (TJ) models with a 5-760X U-joint.
The shafts are positioned for owners with oversized tires and high torque, and they are designed for extended service life. The steel is forged high-grade alloy, heat treated beyond OEM specifications. The shaft and gear set engage through splines, so the 30-spline 97-2031-004 calls for a matching 30-spline differential or carrier. Because an inner shaft spans most of the axle width, its overall length tells you which side of the axle it belongs on.
Key features
- Chromoly inner axle shaft for the Dana 30 front axle
- Driver side, 30 spline, 16.50 inch overall length
- Accepts a 5-760X U-joint
- Machined to accept full circle clips
- Fits Jeep XJ, YJ and TJ models from 1987 to 2006
Matching splines and shaft length
The shaft has to mesh with the carrier, so the spline count at both ends must match the differential side gear it plugs into. Measure the old shaft from end to end and check the spline count before ordering, since a length mismatch can make the shaft bind or pull out of the carrier.
Driver and passenger shafts are different parts, so confirm the side by the overall length and the inner end before you start removing parts. Expect the U-joint and clip set to need replacement at the same time if the old ones show play or wear, and clean the spline area of grease and grit before the new shaft slides in.
Heavier tires put more load and twist through the axle, so the shaft and joints see more stress than stock. Check for play in the joints at every oil change and replace worn parts before they fail away from home.
Specifications
The 97-2031-004 is a chromoly inner axle shaft for the Dana 30 front axle, with 30 splines and an overall length of 16.50 inches. It is used in Dana 30 Reverse and Dana 30 TJ axles.
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 97-2031-004 |
| UPC | 631410097016 |
| Part type | Chromoly inner axle shaft |
| Axle | Dana 30 front (Dana 30 Reverse and Dana 30 TJ) |
| Axle shaft location | Driver side inner |
| Spline | 30 spline |
| Overall length | 16.50 inches |
| U-joint | Accepts 5-760X U-joint |
| Clip design | Machined to accept full circle clips |
| Application stated | 87-06 Jeep XJ/YJ/TJ with 5-760X U-joint |
Vehicle fitment
It fits 87-06 Jeep XJ, YJ and TJ models with a 5-760X U-joint. By chassis code, that covers the 1987-2001 Cherokee (XJ), 1987-1995 Wrangler (YJ) and 1997-2006 Wrangler (TJ).
Application: 87-06 Jeep XJ, YJ and TJ with a 5-760X U-joint.
Check the old shaft’s spline count and length against the 97-2031-004 specifications before you start the job.
It does not fit the Jeep LJ, JK or JL, or any Jeep with a Dana 44 front axle. Confirm the year, model and trim against your vehicle before ordering.
Installation notes
The 30 spline count is a larger spline than the 27 spline shaft listed under the same Dana 30 family, so the matching differential or carrier must also be 30 spline. The shaft accepts a 5-760X U-joint and full circle clips.







