Select your vehicle

G2 Dana 30 JK Chromalloy Outer Axle Shaft – 97-2050-001

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Dana 30 JK driver side outer axle shaft, 32 spline, 6.25 in overall length
  • For 2007-2009 Jeep Wrangler (JK), non Rubicon
  • Chromoly; accepts 5-760X U-joint; machined for full circle clips

Description

Overview

The G2 Axle and Gear 97-2050-001 is a Dana 30 chromoly outer axle shaft for the driver side, with 32 splines and a 6.25 inch overall length. It fits 2007-2009 Jeep Wrangler (JK) non-Rubicon models.

The shafts are forged from high-grade alloy steel and heat treated for high-torque use. The 32 splines on this shaft have to match the gear set inside the axle.

Key features

  • Chromoly outer axle shaft for the Dana 30 JK front axle
  • Driver side, 32 spline, 6.25 inch overall length
  • Accepts a 5-760X U-joint
  • Machined to accept full circle clips
  • It is for 2007-2009 Jeep JK non Rubicon models.

Spline matching and axle wear

An outer axle shaft connects the front differential to the hub, so it works under steering angle and drive torque at the same time. Its condition shows up quickly as clicking through turns or vibration under acceleration. Inspect the shaft and the joint regularly to catch problems while they are small.

Spline count and length decide whether a replacement works in the axle. A shaft that is correct in length but wrong in spline count will not seat, and a mismatched length can change the angle of the joint. Check the U-joint size, clip design and the inside end before buying, since those points decide whether the parts go together.

Keep the boot and joint clean and lubricated. Torn boots let grit in and grease out, which shortens joint life. Replace a cracked or twisted shaft rather than trying to repair it, since failure under load can be sudden.

  • Confirm spline count on both ends
  • Check the U-joint size before buying
  • Inspect the boot for tears
  • Replace shafts that show cracks or twist

Specifications

The 97-2050-001 is a chromoly outer axle shaft (outer stub axle) for the Dana 30 JK front axle, with 32 splines and an overall length of 6.25 inches. Every figure in the table below is the manufacturer value for the 97-2050-001.

Brand G2 Axle and Gear
Part number 97-2050-001
UPC 631410107838
Part type Chromoly outer axle shaft (outer stub axle)
Axle Dana 30 JK front
Axle shaft location Outer stub, driver side
Spline 32 spline
Overall length 6.25 inches
U-joint Accepts 5-760X U-joint
Clip design Machined to accept full circle clips
Application stated 2007-2009 Jeep JK non Rubicon

Vehicle fitment

It fits 2007-2009 Jeep JK non Rubicon models, the Wrangler (JK) for those years.

Application: 2007-2009 Jeep JK non Rubicon.

Match the 97-2050-001 against your old shaft for spline count, length and driver or passenger side before installing it.

Confirm fit for your vehicle’s year, model and trim before ordering, especially for 2010-2018 Wrangler (JK), Wrangler (JL) and Wrangler (TJ).

Installation notes

This is the short outer stub for the driver side of the Dana 30 JK front axle. It accepts a 5-760X U-joint and full circle clips. Confirm those match the existing axle before installing.

SKU: G/297-2050-001 Category:

Specification

Shipping weight 4.00 lbs
Package dimensions 37.00 × 7.50 × 7.30 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (JK) likely fits2007–2009All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What Jeep does the G2 97-2050-001 fit?

It fits 2007-2009 Jeep JK non Rubicon models, which is the Wrangler (JK) with the Dana 30 front axle. Confirm your year and model before ordering.

How many splines does the 97-2050-001 have?

The 97-2050-001 has 32 splines and a 6.25 inch overall length. It is a chromoly outer stub shaft for the driver side that accepts a 5-760X U-joint.

Is the 97-2050-001 an inner or outer shaft?

It is an outer shaft, also called an outer stub axle, for the driver side of the Dana 30 JK front axle. The inner shafts are separate parts.

What signs show an outer axle shaft is failing?

Clicking or vibration in turns, grease on the inside of the wheel, or a shaft that feels loose at the hub are common signs. Inspect the boot and joint, and replace the shaft if it is cracked or twisted.

Should both outer shafts be replaced together?

Not always, but replacing both at the same time is common when one has failed. Matching wear and spline condition on both sides helps the axle stay balanced.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon