Select your vehicle
-13%

G2 Dana 44 JK 07-09 Replacement Axle Shaft – 95-2052-1

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Forged replacement rear axle shaft for 2007–2009 Jeep Wrangler (JK) with a Dana 44 axle
  • 30 spline, 31.50 inch overall length
  • Forged 1541H steel, heat treated
  • Fits both LH and RH positions
  • G2 Axle and Gear part number 95-2052-1

Description

Overview

The G2 95-2052-1 is a forged replacement rear axle shaft for the 2007–2009 Jeep Wrangler (JK) with a Dana 44 axle. It is made from 1541H steel, heat treated, with a 30 spline end and an overall length of 31.50 inches.

G2 Axle and Gear says its high strength axle shafts are engineered to withstand the added load of high torque applications and to remedy common faults found in factory shafts. The shafts are forged from high grade alloy steel and heat treated to exceed OEM specifications, which G2 says is meant for extended service life.

The shaft also uses big spline options, rolled splines and better materials. G2 says these features let owners run larger tires with confidence, without the same risk of failure the factory shaft carries under heavy load.

A spline is the toothed end of the shaft that engages the differential or hub, and the spline count has to match the axle. The shaft is listed with a 5 on 5 bolt pattern and a 2.828 inch brake pilot surface, plus a 1.565 inch bearing surface, which are the points where the shaft meets the hub and the bearing.

Key features

  • Forged 1541H steel, heat treated
  • 30 spline shaft end
  • 31.50 inch overall length
  • Brake pilot surface of 2.828 inches
  • Bearing surface of 1.565 inches
  • 5 on 5 bolt pattern
  • Fits both the LH and RH positions.

Axle shaft wear signs

A rear axle shaft carries the full torque of the drivetrain, so wear shows up as changes in how the vehicle drives. A clicking or popping sound on tight turns can point to a worn joint or shaft, while vibration under acceleration may come from a shaft that has lost its balance or fit. Grease on the inside of the wheel usually means the seal has failed and the bearing needs attention.

Inspect the shaft when the axle is apart for the hub, the splines and the bearing surface. Any groove, pitting or rounded spline is a reason to replace the part rather than run it. Larger tires and hard launches add load, so a shaft that is already marginal should be checked more often.

  • Clicking on tight turns
  • Grease on the inside of the wheel
  • Vibration under acceleration

Specifications

Brand G2 Axle and Gear
Part number 95-2052-1
UPC 631410106466
Axle location Rear
Axle type Dana 44 JK
Material Forged 1541H steel, heat treated
Overall length 31.50 inches
Spline 30
Brake pilot surface 2.828 inches
Bearing surface 1.565 inches
Bolt pattern 5 on 5
Side LH and RH

Vehicle fitment

It is for 2007 to 2009 Jeep Wrangler JK models with a Dana 44 rear axle.

The shaft is for the rear axle, so check that your Jeep has a Dana 44 rear before ordering. The fitment data does not include the 2010 and later Wrangler (JK). Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Axle shaft work involves the bearing and the hub, so have it done by a shop experienced with Dana 44 rear axles. Check the spline count and bolt pattern against your axle before fitting the shaft.

What’s included

The item is one replacement axle shaft for the LH and RH positions. Check the package contents against your installation before starting, including bearings and wheel studs.

SKU: G/295-2052-1 Categories: ,

Specification

Shipping weight 22.00 lbs
Package dimensions 37.00 × 7.50 × 7.30 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (JK) likely fits2007–2009All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will this shaft fit a 2008 Jeep Wrangler JK?

Yes. It is for 2007 to 2009 Jeep JK models with a Dana 44 rear axle, so a 2008 model is in range. Confirm the axle type and trim before ordering.

Is this shaft for the left or the right side?

It fits both the left and right positions, shown as LH and RH. Match the spline count and bolt pattern on your axle before ordering, since those must line up.

Are wheel studs or bearings included?

Check the package contents against your installation for bearings and wheel studs before starting. The shaft has a 30 spline end and a 5 on 5 bolt pattern.

How can I tell an axle shaft is worn?

Look for clicking on tight turns, vibration under acceleration, grease on the inside of the wheel, or a wheel that wobbles when lifted. Any of these signs means the shaft and bearing should be inspected before driving the vehicle further.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon