Select your vehicle
-13%

G2 Dana 30 JK Chromalloy Inner Axle Shaft – 97-2050-003

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Dana 30 JK driver side inner axle shaft, 27 spline, 18.80 in overall length
  • For 2007-2009 Jeep Wrangler (JK) front Dana 30, non Rubicon
  • Chromoly; accepts 5-760X U-joint; machined for full circle clips

Description

Overview

The G2 Axle and Gear 97-2050-003 is a Dana 30 JK chromoly inner axle shaft for the driver side, with 27 splines and an 18.80 inch overall length. It is for 2007-2009 Jeep Wrangler (JK) front Dana 30 non Rubicon models.

The shaft is forged from high-grade alloy steel and heat treated, and it is designed for higher-torque setups. Shaft and gear set engage through splines, so the 27-spline 97-2050-003 calls for a matching 27-spline differential or carrier. Because an inner shaft spans most of the axle width, its overall length tells you which side of the axle it belongs on.

Key features

  • Chromoly inner axle shaft for the Dana 30 JK front axle
  • Driver side, 27 spline, 18.80 inch overall length
  • Accepts a 5-760X U-joint
  • Machined to accept full circle clips
  • For 2007-2009 Jeep JK front Dana 30 non Rubicon models

Inner shaft basics

An inner axle shaft transfers torque from the differential to the wheel assembly, and its inner end carries the wear from the splines and the U-joint. Because the shaft is long, it can flex under load, so checking for bends and worn splines is part of any inspection. The boot and seal near the differential should also be checked for grease leaks.

When replacing the shaft, the U-joint and clips are worth inspecting at the same time. Full circle clips hold the shaft in the differential, so a clean, undamaged groove and a fresh clip are important. Balancing the setup by checking the drive angles after installation helps reduce vibration on the highway.

  • Check splines and U-joint for wear
  • Inspect the boot and seal for leaks
  • Use fresh clips when the shaft is replaced

Specifications

The 97-2050-003 is a chromoly inner axle shaft for the Dana 30 JK front axle, with 27 splines and an overall length of 18.80 inches. Every figure in the table below is the manufacturer value for the 97-2050-003.

Brand G2 Axle and Gear
Part number 97-2050-003
UPC 631410108323
Part type Chromoly inner axle shaft
Axle Dana 30 JK front
Axle shaft location Driver side inner
Spline 27 spline
Overall length 18.80 inches
U-joint Accepts 5-760X U-joint
Clip design Machined to accept full circle clips
Application stated 2007-2009 Jeep JK front Dana 30, non Rubicon, driver side

Vehicle fitment

The shaft is for 2007-2009 Jeep JK front Dana 30 non Rubicon models, driver side, which is the Wrangler (JK) for those years.

The application for the 97-2050-003 is 2007-2009 Jeep JK front Dana 30, non Rubicon, driver side.

Check the old shaft’s spline count and length against the 97-2050-003 specifications before you start the job.

Confirm your vehicle’s year, model and trim before ordering, especially for 2010-2018 Wrangler (JK), Wrangler (JL) or Wrangler (TJ) models.

Installation notes

This is the driver side inner shaft for the Dana 30 JK front axle. It accepts a 5-760X U-joint and full circle clips.

SKU: G/297-2050-003 Category:

Specification

Shipping weight 22.00 lbs
Package dimensions 37.00 × 7.50 × 7.30 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (JK) likely fits2007–2009All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What Jeep does the G2 97-2050-003 fit?

The 97-2050-003 is for 2007-2009 Jeep JK front Dana 30 non Rubicon models, driver side. That is the 2007-2009 Wrangler (JK).

What are the specs of the 97-2050-003?

The 97-2050-003 is a chromoly Dana 30 JK inner shaft with 27 splines and an 18.80 inch overall length. It accepts a 5-760X U-joint and full circle clips.

Is the 97-2050-003 for the driver side?

Yes. It is the driver side inner shaft. Check the spline count and overall length against your old shaft before installing it.

How can you tell if an inner axle shaft is worn?

Common signs include vibration under acceleration, clicking on turns, and grease in the boot or near the inner joint. Inspect the splines and U-joint for wear, and replace the shaft if it is bent or twisted.

Should the clips and seals be replaced with the shaft?

Yes, it is a good idea. Full circle clips and seals are often replaced during the same job, which avoids reopening the axle later.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon