Select your vehicle

G2 Toyota Birfield CV Style Chromoly Inner Axle Shaft – 97-2044-003

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Passenger-side long inner axle shaft, 27 splines
  • Chromoly shaft for the Toyota 9.5 inch front axle
  • Fits the 1975–1990 Toyota Land Cruiser (FJ40 and FJ60)
  • G2 Axle and Gear part number 97-2044-003

Description

Overview

The G2 Axle and Gear 97-2044-003 is a chromoly Birfield CV style inner axle shaft for the passenger side of the front axle on 1975–1990 Toyota Land Cruiser models, including the FJ40 and FJ60.

This long passenger-side shaft has 27 splines for the Toyota 9.5 inch front axle and is made of chromoly. It fits the 75-84 Toyota FJ40 Land Cruiser and the 8/80-1/90 FJ60 Land Cruiser. It is sold as a bare shaft, with no joints included.

Unlike many vehicles, this Land Cruiser axle uses a long shaft on both sides, so there is no short and long pairing to worry about here. Side still matters, because the splines and end details are cut for one side of the axle. The 27 splines are the standard count for the Toyota 9.5 inch axle in this G2 range, and chromoly steel is the material G2 lists. The part is sold as a bare shaft, so joints, seals and hubs are reused or bought separately.

Key features

  • Chromoly inner axle shaft, Birfield CV style
  • Passenger-side long shaft, front right inner position
  • 27 splines
  • Made for the Toyota 9.5 inch front axle
  • Spans FJ40 and FJ60 Land Cruisers
  • Shaft only, with no joints listed

Before you buy

An inner axle shaft carries drive torque from the differential to the joint on the wheel side of the axle. On a solid front axle like the Land Cruiser’s, a worn shaft often shows up as clicking on tight turns or a vibration that climbs with speed. Before ordering, count the splines on the old shaft and measure its length so the new piece matches at both ends.

Shafts are often replaced along with the joints, seals and boots that were already worn. Check the boot for cracks and grease loss, and feel the joint for play. Reusing a loose joint with a new shaft tends to leave the same noise behind. Inspect the hub bolts and axle nut hardware while the axle is apart, since older Land Cruiser hardware is often corroded.

  • Count splines on the old shaft before ordering
  • Inspect CV boots and joint play while the axle is open
  • Replace corroded hub hardware and seals as needed
  • Tighten the axle nut to the value in your service manual

Specifications

Brand G2 Axle and Gear
Part number 97-2044-003
UPC 631410107531
Part type Inner axle shaft, Birfield CV style
Material Chromoly
Axle location Front
Shaft position Passenger side, front right inner
Axle type Toyota 9.5 inches
Spline count 27 splines
Shaft length Long axle

Vehicle fitment

It fits the 1975–1990 Toyota Land Cruiser, covering the FJ40 and the FJ60 generations.

Land Cruisers built before 1975 or after 1990 are outside this fitment, and Toyota Pickups do not apply. The driver-side shaft is a separate part number. Check your year, model and trim against this range before buying.

Installation notes

Since the part serves a 1975 to 1990 range, verify that your front axle is the 9.5 inch Toyota unit before replacing a shaft. Count splines on the old shaft so the joint and shaft match.

SKU: G/297-2044-003 Category:

Specification

Shipping weight 5.50 lbs
Package dimensions 37.00 × 7.50 × 7.30 in
brands

Fitment

VehicleYearsTrims
Toyota Land Cruiser1975–1990Base

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What vehicles does the G2 97-2044-003 fit?

It fits the 1975–1990 Toyota Land Cruiser, covering the 75-84 FJ40 and the 8/80-1/90 FJ60, so both generations are included.

Is the 97-2044-003 a long axle?

Yes. It is the passenger-side long axle in the front right inner position, so it is paired with a driver-side long shaft rather than a short one.

What spline count is the G2 97-2044-003?

It has 27 splines and is sized for the Toyota 9.5 inch front axle. The splines must match the joint and differential parts used with it.

Does the 97-2044-003 include CV joints?

No. G2 lists no joints or hardware with it, so it is an inner axle shaft only and the joints have to be reused or bought separately.

How can I tell the inner axle shaft has worn out?

Common signs are clicking or popping on tight turns, vibration that rises with speed, and grease on the inside of the wheel. A split boot or a loose joint points to the same repair. Lift the vehicle and check the splines for twisting before deciding.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon