Select your vehicle
-13%

G2 Axle and Gear JL Dana 35 Rear 4.10 Ring and Pinion – 1-2149-410

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits the rear Dana 35 AdvanTEK axle of 2018–2026 Jeep Wrangler JL models
  • 4.10 ratio ring and pinion, part number G/21-2149-410
  • Forged 8620 steel, precision-machined to OE specifications
  • Heat treated and lapped for a smoother gear surface

Description

Overview

The G2 Axle and Gear 4.10 ring and pinion set, part G/21-2149-410, replaces the gears in a rear Dana 35 axle. Based on the product title and description, it is made for the Dana 35 AdvanTEK rear axle in 2018–2026 Jeep Wrangler JL models.

G2 builds its Performance Series gears for the increased loads of performance vehicles. A 4.10 ratio is taller than 4.56, 4.88 or 5.13, so it trades some low-speed torque multiplication for lower engine speed on the highway.

Key features

  • Forged from 8620 steel for a strong base
  • Precision-machined to OE specifications with tight tolerances that make setup easier
  • Heat treated to hold up to daily driving
  • Lapped mating surface for a smoother finish and less friction
  • Designed to keep gear noise at OE levels

Choosing a ring and pinion ratio

Gear ratio is the main lever for how the drivetrain feels. A numerically lower ratio like this one keeps engine speed down on the highway, which reduces noise and fuel use on long drives. The trade-off is weaker acceleration from a stop and less pulling power when climbing with a loaded vehicle or larger tires.

A ring and pinion swap is usually done alongside a fresh set of bearings, shims and seals, since those parts set the mesh. Tire diameter, transmission gearing and transfer case ratio all affect the result, so check the whole driveline before committing. A professional setup with gauges is the normal way to finish a gear change.

  • Check tire diameter before ordering
  • Replace the pinion crush sleeve during install
  • Verify the axle type on the vehicle

Specifications

Brand G2 Axle and Gear
Part number G/21-2149-410
Axle location Rear
Axle type Dana 35 AdvanTEK
Gear ratio 4.10
Material 8620 steel, forged
Surface Lapped mating surface

Vehicle fitment

Based on the product title and description, this set is for the rear Dana 35 axle of 2018–2026 Jeep Wrangler JL models.

Earlier Wrangler generations, including the JK (2007–2018), fall outside these years. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Ring and pinion sets like this one are normally set up by a professional, who checks pinion depth, carrier preload and backlash before the axle returns to service. Break the new gears in gradually, and support the vehicle securely before working under it.

What’s included

One ring and pinion gear set for the rear Dana 35 axle.

Not included: the bearings, shims, pinion nut, crush sleeve and seals needed to install the set.

Fitment

VehicleYearsTrims
Jeep Wrangler (JL) likely fits2018–2026All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will this G2 4.10 ring and pinion fit a 2018–2026 Jeep Wrangler JL?

Yes, it is made for the rear Dana 35 AdvanTEK axle on 2018–2026 Jeep Wrangler JL models. Confirm your year, model and trim before ordering, and check the axle type on your vehicle.

Is the 4.10 ratio taller or shorter than 4.56?

It is taller. A numerically lower ratio like 4.10 keeps engine speed down at highway speed, but it gives less torque multiplication off the line than 4.56 or 5.13, which is why drivers with larger tires often step up in ratio.

Does this set include the install hardware?

No. The set is the gear pair only, so bearings, shims, the pinion nut, the crush sleeve and seals must be bought separately before the rear Dana 35 can be assembled with these gears.

Are these gears forged?

Yes. G2 forges the gears from 8620 steel, precision-machines them to OE specifications, heat treats them for durability and laps the mating surface for a smoother finish.

Does a lower ratio change how the engine works at highway speed?

Yes, it keeps engine speed lower at a given road speed, which can reduce highway noise. Low-speed pulling power drops, so drivers who tow or run big tires often notice the change off the line.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon