Overview
The Dana Spicer 29903-1X is a GM 8.5 inch 10 bolt front passenger side inner axle shaft, 19.15 inches long with 28 splines, for 1979–1989 GM K10 and K20 trucks and 1979–1987 K5 Blazers. Dana Spicer describes its replacement axle shafts as the shafts that came in the vehicle from the factory, so there is no question of poor fitment. The 29903-1X is the inner shaft for the front passenger side, intended for use with the 5-760X u-bolt.
It is made from micro-alloy material and is controlled heat treated for hardness. It covers Chevrolet and GMC pickups, Blazers, Jimmys and Suburbans.
Key features
- Front passenger side inner axle shaft
- GM 8.5 inch 10 bolt front axle
- 28 splines
- 19.15 inches overall length
- For use with the 5-760X u-bolt
- Micro-alloy material.
- Controlled heat treatment for hardness.
Checking the axle before install
A front axle shaft transfers power from the differential to the wheel hub, and on a solid axle it moves up and down with suspension travel. The inner end carries the splines that engage the side gear, so the spline count has to match on both ends of the shaft. Before pulling the old shaft, compare the spline count, length and axle type against the part you removed, and inspect the splines for twisting, pitting or rounded edges.
Axle shafts often wear together with the seals and bearings around them. A leaking axle seal can dump gear oil onto the shaft and cause the bearing to fail early. When replacing one shaft, check the opposite side for wear, since shafts usually age at a similar rate. Check the retaining hardware and clean the splines before assembly so the new shaft seats properly.
Confirm that the u-bolt and hub hardware are in good condition before reassembly. Once the truck is back on the road, look for leaks at the axle seal and listen for new clicks on turns, which can signal a shaft or joint that needs another look.
Specifications
| Brand | Dana Spicer |
|---|---|
| Part number | 29903-1X |
| Axle manufacturer | GM |
| Axle position | Front |
| Shaft location | Passenger Side Inner |
| Axle type | GM 10 Bolt 8.5 Inches |
| Position | Front Right |
| Spline count | 28 Splines |
| Overall length | 19.15 inches |
| Material | Micro-alloy |
| For use with | 5-760X u-bolt |
| Applications noted | 79-89 GM K10/K20 trucks, 79-87 GM K5 Blazer |
Vehicle fitment
Trim levels are given with each model and year range.
- 1987–1991 Chevrolet Blazer (Custom Deluxe, Scottsdale, Silverado)
- 1984–1986 Chevrolet K10 (Custom, Scottsdale, Silverado)
- 1984–1986 Chevrolet K10 Suburban (Custom, Scottsdale, Silverado)
- 1984–1986 Chevrolet K20 (Custom, Scottsdale, Silverado)
- 1984–1986 Chevrolet K20 Suburban (Custom, Scottsdale, Silverado)
- 1984–1986 Chevrolet K30 (Custom, Scottsdale, Silverado)
- 1984–1986 Chevrolet K5 Blazer (Custom, Scottsdale, Silverado)
- 1987 Chevrolet V10 (Custom Deluxe, Scottsdale, Silverado)
- 1987–1988 Chevrolet V10 Suburban (Custom Deluxe, Scottsdale, Silverado)
- 1989–1991 Chevrolet V1500 Suburban (Scottsdale, Silverado)
- 1987 Chevrolet V20 (Custom Deluxe, Scottsdale, Silverado)
- 1987–1988 Chevrolet V20 Suburban (Custom Deluxe, Scottsdale, Silverado)
- 1989–1991 Chevrolet V2500 Suburban (Scottsdale, Silverado)
- 1987–1988 Chevrolet V30 (Cheyenne, Custom Deluxe, Scottsdale, Silverado)
- 1989–1991 Chevrolet V3500 (Cheyenne, Scottsdale, Silverado)
- 1984–1991 GMC Jimmy (Base, High Sierra, Sierra Classic)
- 1984–1986 GMC K1500 (Base, High Sierra, Sierra Classic)
- 1984–1986 GMC K1500 Suburban (Base, High Sierra, Sierra Classic)
- 1984–1986 GMC K2500 (Base, High Sierra, Sierra Classic)
- 1984–1986 GMC K2500 Suburban (Base, High Sierra, Sierra Classic)
- 1984–1986 GMC K3500 (Base, High Sierra, Sierra Classic)
- 1987 GMC V1500 (Base, High Sierra, Sierra Classic)
- 1987–1991 GMC V1500 Suburban (Base, High Sierra, SLE, Sierra Classic)
- 1987 GMC V2500 (Base, High Sierra, Sierra Classic)
- 1987–1991 GMC V2500 Suburban (Base, High Sierra, SLE, Sierra Classic)
- 1987–1991 GMC V3500 (Base, High Sierra, SLE, Sierra Classic)
Only the models and year ranges above are covered. GM trucks with other axle sizes, and models outside each range, need different shafts. Confirm your vehicle’s year, model and trim before ordering.





