Select your vehicle

Currie Pinion Yoke – 60-1350

Currie

Shop Currie Differential Pinion Yokes on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Currie 60-1350 pinion yoke for Dana 60 axles, designed to run the 1350 series U-joint
  • Fits Dana 70 and Dana 61 axles in the front or rear location
  • Part number 60-1350, UPC 70000201131
  • No vehicle fitment listed; confirm your axle type before ordering

Description

Overview

The Currie 60-1350 is a pinion yoke for Dana 60 axles that lets you run the 1350 series U-joint. It also fits Dana 70 and Dana 61 axles, in either the front or rear axle location. The yoke attaches to the pinion gear inside the differential and carries the driveshaft U-joint, so the yoke size sets which U-joint can be used.

Key features

  • Built to run the 1350 series U-joint on Dana 60 axles
  • Fits Dana 60, Dana 70 and Dana 61 axle types
  • Covers both front and rear axle locations
  • Manufacturer number CUR60-1350

Choosing a U-joint size

The yoke size sets which U-joint can be used, so the 1350 series joint and the yoke have to be matched as a pair. Different joint series use different cup diameters, and mixing them causes binding or joint failure under load. Driveshaft length and pinion angle also affect joint life, so check both when the driveline is changed.

Off-road loads put more stress on the joint than daily driving does. Grease the joint at the interval your driving calls for, and look for play, dry seals or rust on the cups at each service. A worn joint can make a clunk or vibration that often starts when the throttle is changed.

  • Match the U-joint series to the yoke
  • Measure cup diameter before buying a joint
  • Check driveshaft angle when the vehicle is lifted
  • Inspect joint cups and seals at each service

Specifications

Brand Currie
Part number 60-1350
Manufacturer number CUR60-1350
UPC 70000201131
Axle location Front or rear
Axle types Dana 60, Dana 70, Dana 61
U-joint series 1350 series

Vehicle fitment

This yoke is matched by axle type. Identify your axle as Dana 60, Dana 70 or Dana 61 before ordering.

Axles other than the Dana 60, Dana 70 and Dana 61 types named here are not covered. Confirm your vehicle’s year, model and trim before ordering.

What’s included

The pinion yoke only. No other hardware is described.

Not included: a 1350 series U-joint, which is needed to use this yoke.

SKU: CUR60-1350 Category:

Specification

Shipping weight 5.00 lbs
Package dimensions 6.00 × 6.00 × 6.00 in
brands

Questions & Answers

What is the Currie 60-1350 pinion yoke?

It is a Currie pinion yoke, part number 60-1350, made for Dana 60 axles. It is designed to run the 1350 series U-joint, and it also fits Dana 70 and Dana 61 axles in front or rear locations.

Will the 60-1350 yoke fit my vehicle?

This yoke is matched by axle type. Confirm your axle is a Dana 60, Dana 70 or Dana 61 type, then confirm your vehicle's year, model and trim before ordering.

Does this yoke work with a 1350 series U-joint?

Yes. Currie designed this yoke to run the 1350 series U-joint on Dana 60 axles. The U-joint itself is not included and must be obtained separately.

How do you tell a U-joint is worn?

Look for play in the joint when the driveshaft is turned by hand, rust or dry seals on the cups, and a clunk or vibration when the drive shifts between throttle and coast. Replace the joint before it fails on the trail, and check the yoke ears for damage at the same time.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Currie Differential Pinion Yokes on Amazon