Select your vehicle

UTV LED Whips are the lighted safety flags that make a side-by-side visible over dunes and through dust at night: 4 and 6 foot whips from Buggy Whip, Gorilla Whips and Quick Light in single colors or red, white and blue and red, white and green combinations, with threaded or quick release bases, plus the quick release pole bases and vertical bar mounts that hold them.Choose the length and base type that match your mount, then compare the products below.

Showing 1–12 of 29 resultsSorted by popularity

Why run a lighted whip

In dunes and open desert the biggest danger is another vehicle you cannot see over the next rise. A tall whip with a flag has been the answer for decades, and many riding areas require one at a minimum height. An LED whip adds light to the flag so the same visibility works at night, and the colors let a group pick out its own machines in a crowd. Whips of this type are also popular on Jeeps and trucks for the same reason, though the mounts here are aimed at UTV cages and bed rails.

Length and brightness

Four and six foot whips are the common sizes. A 6 foot whip puts the light and flag well above the roll cage, which is what dune rules usually want; a 4 foot whip is less likely to catch trees and overhead branches on wooded trails and clears a garage door. Brightness is quoted in LED count and lumens: the Buggy Whip 6 foot models list more than 1,000 LEDs and over 6,000 lumens, the 4 foot models over 700 LEDs and 4,000 lumens. Quick Light builds its 6 foot whip around a 5/8 inch thick Lexan fiber optic core lit by CREE LEDs. More light is more visible, and also more current draw and more glare in the mirrors of the driver behind you, which is why single color whips and dimmer settings exist.

Threaded or quick release base

  • A threaded base screws into a matching mount, like the Buggy Whip QM2, and can also be run on other 3/8 or 1/2 inch threaded whip mounts; check the thread.
  • A quick release base drops into a mount such as the Buggy Whip QRL03 or the Quick Light pole base and locks with a hitch pin, so the whip comes off in seconds for trailering, garages and overhead clearance.
  • Bases and mounts are brand specific. A Buggy Whip quick release whip needs its own mount; Quick Light whips use Quick Light bases.
  • Look at base material. Buggy Whip uses a 316 stainless steel base, which matters when the whip is bent repeatedly and sprayed with salt or dust.

Mounting

Whips take a beating from wind at speed and from the lever arm of a 6 foot pole, so the mount needs to bolt to something solid: a bed rail bracket, a cage clamp or a vertical bar mount like the Gorilla Whips piece. Mount at the rear of the machine, high enough that the flag clears the cage and roof. Tube clamps must match the cage tube diameter closely, and a strip of rubber inside the clamp stops it rotating. Wire the whip through a fuse and a switch, or the remote supplied with it, and route the lead so the whip can be removed without cutting anything. Many whips take a standard 12 volt feed with a two wire connector at the base.

Rules and etiquette

Dune areas often specify a minimum flag height above the ground, a flag size and sometimes a color, and some restrict red or blue lights that could be confused with emergency vehicles on the road. Rules vary by state and by riding area, so check before you go. On the trail, dim or turn off a bright whip when stopped near other riders, and switch it off entirely on public roads unless local law allows it.

Popular UTV LED Whips brands

UTV LED Whips FAQ

Should I choose a 4 foot or 6 foot LED whip?

A 6 foot whip is the usual choice for dunes and open desert, where height over the cage is what makes you visible. A 4 foot whip suits wooded trails, trailers and garages where a taller pole would catch. Check the minimum flag height for your riding area.

What is the difference between a threaded and a quick release whip?

A threaded whip screws into a matching threaded mount. A quick release whip drops into a mount and locks with a pin, so it comes off in seconds for trailering or low clearance. Bases and mounts are brand specific, so match the whip to its own mount.

How do I wire an LED whip?

Most whips take a 12 volt feed through a two wire lead at the base. Run the positive through a fuse and a switch or the whip's controller, ground to the chassis, and route the wiring so the whip can be unplugged and removed. Keep connectors sealed against dust and water.

Are LED whips legal on the street?

Rules vary. Many states treat colored or flashing lights, especially red and blue, as restricted on public roads, and riding areas have their own flag and light rules. Use the whip off-road and check local regulations before running it anywhere else.