Nameplates, Emblems & Decals
Showing 25–35 of 35 resultsSorted by popularity
-
-
-
-
-
-
Emblems and Nameplates
Omix-ADA Jeep Emblem (Black/Chrome) – DMC-5451627
- Omix-ADA black and chrome Jeep emblem, part number DMC-5451627
- Stick-on with pre-applied double sided adhesive tape
- Reproduces the emblem mounted on rear corner panels from 1972 on
- Officially licensed MOPAR product
SKU: OAIDMC-5451627 -
-
What you will find here
This category is mostly die-cut exterior vinyl: small logo decals from 2 inches up to 28 inch hood graphics, Rubicon-style hood stripes sold individually, windshield banners and side panel designs. The emblem side covers factory and aftermarket badges that attach with adhesive tape or clips. Nearly all of it is universal fit by design, though the large hood decals are cut to a specific Jeep hood, such as the YJ and JK Mountain Spyder graphics, and the fender dragon decal is a Mopar part for a particular body.
Choosing a decal
- Size and placement: small 2 by 3 inch logos suit fenders, corners, doors and toolboxes. A 12 inch logo reads from across a parking lot. Hood stripes around 22 inches long are sized to the raised section of a Wrangler hood and are ordered two at a time for both sides.
- Material: look for automotive exterior grade cast or calendared vinyl. Cast vinyl stretches around curves and holds up longer in sun; calendared vinyl is fine on flat panels. The 3 mil matte black vinyl used on the Rugged Ridge side decals is typical.
- Color and finish: a black decal on a black Jeep works only in a contrasting finish, such as matte on gloss. White and silver show on dark paint; the Knife Blade multicolor design makes a statement on a plain hood.
- Single color or printed: single-color die-cut decals have no background and look painted on. Printed graphics have a clear or colored background that can be visible at the edges.
Applying large hood decals
Decals such as the Mountain Spyder hood graphics are big enough that the makers recommend professional installation. If you do it yourself, work indoors or in shade on a day between about 60 and 80 degrees F. Wash the panel, then wipe it with isopropyl alcohol to remove wax. Position the decal with masking tape hinges, measure from fixed body features on both sides, and apply wet with a fine mist of water with a drop of soap for anything larger than a hand. Squeegee from the center outward, lift the transfer tape at a sharp angle, and let the decal cure for a day before washing. Small decals go on dry.
Emblems and nameplates
Factory emblems attach with foam tape or with pins that push into holes in the panel. Before removing an old emblem, warm it with a hair dryer and lift it with fishing line, then remove tape residue with an adhesive remover. A new tape-mounted emblem needs the same clean, alcohol-wiped surface as a decal and firm pressure for about a minute. Pin-mounted emblems need the correct hole pattern, so compare the back of the new emblem with the old one.
Durability and removal
Quality exterior vinyl lasts several years in full sun, longer in a garage. Pressure washers can lift edges, so keep the wand a couple of feet away. Decals come off with heat and patience, and the paint underneath will be slightly less faded than the surrounding panel on an older vehicle. Nothing here affects fitment or safety, so the only check before choosing is the size against your panel and, for hood graphics, the exact Jeep generation named.
Popular Nameplates, Emblems & Decals brands
- Jeep (12)
- Poison Spyder Customs (8)
- Putco (6)
- Omix-Ada (6)
- Rubicon Express (2)
- Rock Hard 4x4 Parts (1)
- Rugged Ridge (1)
- G2 Axle and Gear (1)
Shop Nameplates, Emblems & Decals by type
- Emblems and Nameplates (19)
- Decals (16)
Nameplates, Emblems & Decals FAQ
Do I need two hood stripes for a Rubicon-style look?
Yes. The Rubicon and Spyder style hood decals in this category are sold individually, and the factory look uses one on each side of the hood's raised center. Order two of the same color and apply them at the same distance from the hood edge.
Can I put a decal over a textured or plastic surface?
Smooth painted plastic takes decals well. Heavily textured plastic, such as fender flares or rocker guards, does not give enough contact area and the decal will lift at the edges within weeks. Stick to painted metal, gloss plastic or glass.
How do I remove an old decal without damaging paint?
Warm it with a hair dryer or heat gun on low until the vinyl softens, then peel slowly at a low angle. Remove leftover adhesive with a citrus or automotive adhesive remover and a microfiber cloth, then wash and wax the panel. Avoid razor blades on paint.
Will a windshield banner block my view?
A banner placed in the top few inches of the windshield, above the sweep of the wipers and the tinted band area, generally does not affect vision. State rules on how far a windshield decal may extend vary, so check local regulations before applying one.









