Select your vehicle
-13%

Pro Comp PRO-M Monotube Front Shock Absorber – PR2056

Pro Comp Suspension

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Pro Comp PRO-M front monotube shock, part PR2056, sold individually
  • Designed for 4 inches of lift
  • Extended 24.4 in, collapsed 15.6 in
  • Fits the 1997 to 2006 Jeep Wrangler TJ and 2004 to 2006 Wrangler LJ

Description

Overview

The Pro Comp Suspension PR2056 is a PRO-M front monotube shock for Jeep Wranglers with a 4 inch lift. It fits the 1997 to 2006 Wrangler TJ and the 2004 to 2006 Wrangler LJ, and it is sold individually.

The shock is nitrogen gas charged and uses a floating piston to separate oil from the gas. It has a larger body for extra oil capacity and a multi-stage disc pack tuned for the application.

Key features

  • Front monotube design for a 4 inch lifted Wrangler
  • Extended length 24.4 inches, collapsed length 15.6 inches
  • Nitrogen gas charged with floating piston
  • Multi-stage disc pack valving, vehicle specific
  • 14 mm chrome hardened shaft
  • Polyurethane shock boot included

Matching shock length to lift

Front shock length sets how the Wrangler sits at each corner and how much travel the suspension can use. When a lift raises the body, the new shock has to cover a different range, so measure the installed length of the old unit before buying. A shock that is too short can bottom out on rough ground, while one that is too long can strain the mounts and limit steering angle.

Front dampers work hardest on steep descents and rock crawling, so bushings, seals and boots wear over time. Look for oil on the shock body, a loose or noisy mount, and a boot that has split or pulled off the shaft. Replacing both front shocks together keeps the two sides of the axle responding the same way on uneven ground.

  • Measure the old shock’s installed length before ordering
  • Inspect the bushings and mounts at each oil change
  • Check the boot for cracks after trail use

Specifications

Brand Pro Comp Suspension
Part number EXPPR2056
Shock series PRO-M
Position Front
Extended length 24.4 in
Collapsed length 15.6 in
Upper and lower mount Loop
Lift 4 in
Finish Silver powder coat

Vehicle fitment

It fits the 2004 to 2006 Jeep Wrangler (LJ), including the Unlimited and Unlimited Rubicon, and the 1997 to 2006 Jeep Wrangler (TJ), including the 65th Anniversary Edition, Rubicon, SE, Sahara, Sport and X models.

It is made for the TJ and LJ Wrangler generations only. Confirm fit for your vehicle’s year, model and trim before ordering.

Installation notes

Compare the 24.4 inch extended and 15.6 inch collapsed lengths with the front shock being replaced, because a 4 inch lift changes the ride height. The loop mounts at both ends should line up with the Wrangler’s factory brackets. Check the boot for a secure fit and confirm there is clearance from the frame and axle at full compression.

With a 4 inch lift on a TJ or LJ, the front suspension geometry changes, so check the alignment after installation. Confirm the loop mounts are tight, the shock clears the frame at full compression, and the polyurethane boot is seated on the shaft.

Check that the front shock body clears the steering linkage and the brake hose at full lock, and confirm the mounts do not bind when the front axle articulates.

What’s included

One PRO-M front monotube shock with polyurethane boot under part number EXPPR2056.

Fitment

VehicleYearsTrims
Jeep Wrangler (LJ)2004–2006Unlimited, Unlimited Rubicon
Jeep Wrangler (TJ)1997–200665th Anniversary Edition, Rubicon, SE, Sahara, Sport, X

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the PR2056 fit a 2005 Jeep Wrangler LJ?

Yes. It fits the 2004 to 2006 Wrangler LJ, which includes 2005 models in the Unlimited and Unlimited Rubicon trims. Confirm fit for your vehicle's year, model and trim before ordering.

Is the PR2056 for a 4 inch lift?

Yes. It is designed for Wranglers with a 4 inch lift. The shock has a 24.4 inch extended length and a 15.6 inch collapsed length, so compare these with the front shock being replaced before fitting.

Does it fit a JK?

No. It is designed for the TJ and LJ Wrangler generations, so a JK needs a shock built for its own model. Confirm fit for your vehicle's year, model and trim before ordering.

How can I tell when a front shock needs replacing?

Look for oil leaking down the body, a clunk or knock over bumps, and uneven front tire wear. A shock that no longer controls rebound on washboard roads is also a sign of wear. Inspect the mounts and boot at the same time.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon