Select your vehicle
-13%

Pro Comp 4″ Stage I Lift Kit with PRO-X Shocks – K4069T

Pro Comp Suspension

Shop Ford Bronco Lift Kits on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits 1980 to 1989 Ford Bronco models
  • 4-inch stage 1 lift with PRO-X front and rear shocks
  • Add-A-Leaf rear lift
  • Lift height range of 4 to 5.5 inches

Description

Overview

The Pro Comp 4-inch Stage I Lift Kit with PRO-X Shocks, part number EXPK4069T (kit K4069T), is a stage 1 suspension lift for the 1980 to 1989 Ford Bronco, across its Custom through XLT Lariat trims.

The kit provides 4 inches of stage 1 lift, with a listed lift height range of 4 to 5.5 inches. The rear uses an Add-A-Leaf lift, and PRO-X shocks are included at the front and the rear.

Key features

  • 4-inch stage 1 suspension lift
  • Add-A-Leaf rear lift
  • PRO-X shocks at the front and rear, included
  • Lift height range of 4 to 5.5 inches

Clearance and tire choice

A 4-inch stage 1 lift makes room for larger tires, but clearance depends on the tire’s overall diameter, width and offset, along with fender and body clearance on your particular Bronco. Measure before buying tires, and remember that taller tires change gearing and speedometer reading. Bigger tires also add load to the drivetrain, so joints and wheel bearings deserve attention.

On the trail, the lift raises the center of gravity slightly, which is worth considering on side slopes. Consider bump stops and fender trimming if the tires rub at full compression. Check tire pressures and wear regularly, since larger tires can wear differently on this type of setup.

  • Measure fender clearance at full compression
  • Check the speedometer after changing tire size
  • Inspect wheel bearings after larger tires

Specifications

Brand Pro Comp Suspension
Part number EXPK4069T
Kit code K4069T
Suspension type Lift kit, stage 1
Lift height 4 inches stage 1; range 4 to 5.5 inches
Rear lift method Add-A-Leaf
Rear lift component Add-A-Leaf
Shocks included Yes
Front shocks PRO-X
Rear shocks PRO-X
Fit type Direct fit

Vehicle fitment

It is a direct fit for the 1980 to 1989 Ford Bronco in the Custom, Eddie Bauer, Ranger XLT, XLS, XLT and XLT Lariat versions.

The list does not include the 1979 and earlier Bronco or the 1990 and newer models, which are covered by a different listing. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The Add-A-Leaf rear lift changes the rear ride height and the driveline angle, so the driveline and alignment should be checked after installation.

What’s included

The 4-inch stage 1 lift kit with PRO-X front and rear shocks, and the Add-A-Leaf rear component.

SKU: EXPK4069T Categories: ,

Fitment

VehicleYearsTrims
Ford Bronco1980–1989Custom, Eddie Bauer, Ranger XLT, XLS, XLT, XLT Lariat

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the Pro Comp K4069T fit a 1985 Ford Bronco?

Yes. It fits 1980 to 1989 Ford Bronco models, and 1985 falls within that range. Confirm the trim before ordering.

Does it fit a 1991 Bronco?

No. The Bronco list for this kit ends with 1989. The Bronco entries for this kit run from 1980 to 1989.

What is the tire size?

Confirm tire clearance for your chosen size before ordering. The kit gives 4 inches at stage 1, with an Add-A-Leaf rear and PRO-X shocks at both ends.

Do larger tires need changes after a lift?

Yes. Larger tires usually call for a speedometer recalibration and a fender clearance check, and they can affect braking. Recheck the wheel bearings and joints after the first few trips.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Ford Bronco Lift Kits on Amazon