Overview
The Poison Spyder PSC17-16-021-DSP1 is a BFH II front bumper with a Trail Stinger for the Jeep Wrangler JK (2007-2018), in semi-gloss black SpyderShell Armor Coat. It is a lightweight, high clearance “stubby” bumper made of 3/16″ plate steel.
The Trail Stinger follows the proportions of the earlier Trail Stinger built for the TJ, YJ and CJ, and its rake matches the angle of the bumper face so it can act as a ramp onto obstacles. It extends 13.4″ forward of the bumper’s front edge and is 17″ high from the top surface. The bumper is just slightly wider than the frame rails and has provisions for the factory fog lights in recessed buckets. The Wrangler 10th Anniversary Rubicon fog lamps do not fit those buckets.
Key features
- Lightweight, high clearance stubby bumper design
- Trail Stinger from 1.5″ X .120 wall DOM tubing with 3/16″ plate steel gussets
- Stinger extends 13.4″ forward and is 17″ high
- Integrated winch mount with 10″ X 4-1/2 and 6 X 4-1/2 bolt patterns
- Recessed fog lamp buckets, with Rigid Dually lights possible through an adapter plate
- Heavy duty shackle tabs machined from 1″ thick plate steel
- SpyderShell Armor Coat with a 5-year warranty on materials and workmanship
Winching and recovery setup
A stubby front bumper with a stinger changes how a winch behaves. The mount sits close to the front of the vehicle, so line pull and cable angle matter more than they would on a longer bumper. Keep the fairlead centered on the winch and check that the cable runs clear of the bumper face and the tabs.
Shackle tabs take heavy loads, so use shackles that match the tab stock and never attach straps or chain to the bumper body. Inspect the welds around the stinger and gussets after recovery, especially after a hard angled pull, since those joints carry most of the force.
Heavy use can also loosen the protective skid and nearby brackets, so check fasteners after rough trails. A bumper that sits high and wide changes approach and departure angles, so practice slow approaches before tackling new obstacles.
- Use shackles sized for the tab stock
- Keep the cable centered through the fairlead
- Inspect welds after angled pulls
- Recheck bolts after rough trail use
Specifications
| Brand | Poison Spyder |
|---|---|
| Part number | PSC17-16-021-DSP1 |
| UPC | 614901764918 |
| Type | BFH II front bumper with Trail Stinger |
| Material | 3/16″ plate steel |
| Finish | SpyderShell Armor Coat, semi-gloss black |
| Stinger tubing | 1.5″ X .120 wall DOM |
| Stinger projection | 13.4″ forward, 17″ high |
| Winch patterns | 10″ X 4-1/2 and 6 X 4-1/2 |
| Shackle tab stock | 1″ thick plate steel, for 3/4″ shackles |
Vehicle fitment
It is built for the Jeep Wrangler JK, 2007-2018.
It is designed for the JK rather than the TJ, LJ or JL. Confirm fit for your vehicle’s year, model and trim before ordering.
Installation notes
A winch fairlead and fairlead mount are needed separately. The optional JK BFH II Disco Skid is a bolt-on skid plate that protects the factory electric swaybar disconnect motor and includes hardware and instructions to rotate the motor upward.
What’s included
- BFH II front bumper with Trail Stinger
- Heavy duty recovery shackle tabs
- Recessed fog lamp buckets
Not included: a winch, fairlead, fairlead mount and the optional JK BFH II Disco Skid.














