Overview
The Icon Suspension Uniball Upper Control Arm Kit, part number 98500, is a tubular upper control arm system for the 2004–2018 Ford F-150 in 2WD and 4WD trucks. Icon Vehicle Dynamics built it to replace the factory ball joint setup, which can limit suspension travel, especially when the truck runs Icon’s 2.5 inch VS Series performance coil-over shocks.
Each arm pairs 1 inch PTFE lined stainless uniballs with a 17-4 stainless taper pin adapter. That combination increases upper arm misalignment, which Icon says allows smooth and clean wheel travel without factory ball joint bind. The arms are built from 1026 DOM seamless tubing that is CNC bent, and the uni-ball cup and adapter pin are CNC machined.
A two stage bushing kit comes standard. It uses polyurethane bushings with a delrin anti-deflection ring to reduce deflection and improve durability and road response. The bushing housings and sleeves are CNC machined and greasable, and the arms are professionally precision welded.
Key features
- Tubular upper control arms in 1026 DOM seamless tubing, CNC bent
- Dual stage bushing design for durability and response
- Polyurethane bushings with delrin anti-deflection ring
- CNC machined greasable bushing housings and sleeves
- CNC machined uni-ball cup and 17-4 stainless uni-ball adapter pin
- PTFE lined stainless uniballs
- Professionally precision welded construction
- Factory wheels and tires can be used
Before you install
Upper control arms locate the axle laterally and control the wheel’s fore-and-aft position, so their joints carry load every time the suspension moves. On a lifted truck, arm angles change and standard ball joints can bind near the end of travel. Uniball joints tolerate more misalignment, which is why they are common in lift setups. Joint wear shows up as clunks over bumps, wandering on the highway, or uneven tire wear, and these symptoms are worth checking before any new arm goes on.
Before buying, confirm that the truck’s steering knuckles, shock mounts and wheel offset work with the new arms, and that the wheel back space meets the size range. Grease the bushing housings during routine service, because dry bushings wear faster. When the arms are replaced, check the alignment afterward and inspect the tie rod ends and sway bar links, which are often serviced at the same time. Keep the bolt torque to the factory setting.
- Check steering knuckle and shock clearance
- Grease bushing housings at routine service
- Re-check alignment after the first drive
Specifications
| Brand | Icon Suspension |
|---|---|
| Part number | 98500 |
| UPC | 70000624064 |
| Position | Upper |
| Drivetrain | 2WD and 4WD |
| Tubing | 1026 DOM seamless |
| Uniballs | 1 inch PTFE lined stainless |
| Uniball adapter pin | 17-4 high grade stainless steel |
| Bushings | Polyurethane with delrin anti-deflection ring, dual stage |
| Aftermarket wheels | 17-inch or larger with max 5-inch back space (some 16-inch wheels may fit) |
| Tire sizes noted | 33 or 35 x 12.50 |
| Fit type | Direct fit |
Vehicle fitment
The kit fits the 2004–2018 Ford F-150 in 2WD and 4WD trucks, across a broad trim list that includes FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lariat Limited, Limited, Platinum, Raptor, SSV, STX, SVT Raptor, 60th Anniversary Edition, XL and XLT.
The fit range covers non-Raptor models and also includes Raptor and SVT Raptor trims. Confirm fit for your vehicle’s year, model and trim before ordering.
Installation notes
Factory wheels and tires can be used. For aftermarket wheels, follow the size guidance in the specifications, since some 16-inch wheels may fit while 17-inch or larger wheels with max 5-inch back space are the stated baseline. The bushing housings are greasable, so include them in routine service.
What’s included
The kit includes the tubular upper control arms with the dual stage polyurethane bushings, delrin anti-deflection rings and PTFE lined stainless uniballs described above.
Not included: the 2.5 inch VS Series coil-over shocks referenced in the overview are not part of this kit.


