Select your vehicle
-13%

G2 XJ Cherokee Front and Rear 4.88 Ring and Pinion Kit – 4-XJ4-488

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits 1984 to 2001 XJ Cherokee
  • Front Dana 30 reverse 4.88 and rear Dana 44 4.88
  • Includes matched front and rear master installation kits
  • Computer heat treated 8620 steel, double shot peened
  • Limited lifetime warranty

Description

Overview

The G2 Axle and Gear 4-XJ4-488 is a 4.88 ratio front and rear ring and pinion kit for the Jeep Cherokee XJ. The kit is stated to fit 1984 to 2001 XJ Cherokee models. It pairs a Dana 30 reverse front gear set for a 3.73 and up carrier with a Dana 44 rear gear set for a 3.91 and up carrier.

G2 says these gears are designed to hold up to oversized tires and high performance engines. Both gear sets and both master installation kits come in the same box.

Key features

  • Front and rear 4.88 ring and pinion sets in one kit
  • Dana 30 reverse front gears for a 3.73 and up carrier
  • Dana 44 rear gears for a 3.91 and up carrier
  • Matched front and rear master installation kits
  • Double shot peened and double lapped, with 8620 steel gears

Gear swap planning

Changing to a 4.88 ratio on both axles is more than a single gear set swap, so plan the work before the parts arrive. The front and rear gears are matched to their own carriers, and pinion and carrier bearings are commonly replaced at the same time. Inspect the old carriers for wear, scoring or a cracked case. A worn carrier can cause noise even with new gears installed.

Gear mesh is the step most often rushed. Set pinion depth first, then bearing preload, then backlash, and check the tooth contact pattern with marking compound before the axles go back on the Jeep. Clean the housings well and fill with fresh gear oil to the correct level. Recheck the mesh and fastener torque after the first short drives, because new gears settle as they bed in.

  • Replace pinion and carrier bearings with the gears
  • Inspect axle seals and replace any that leak
  • Use a gear oil suited to your axle type

Specifications

Brand G2 Axle and Gear
Part number 4-XJ4-488
UPC 700007521821
Gear ratio 4.88
Front axle Dana 30 reverse, 3.73 and up carrier
Rear axle Dana 44, 3.91 and up carrier
Material Computer heat treated 8620 steel
Warranty Limited lifetime

Vehicle fitment

It fits 1984 to 2001 XJ Cherokee models equipped with the Dana 30 reverse front and Dana 44 rear axles. Fit follows those model years and the XJ name.

The years stop at 2001, so the XJ generation is covered and the later Liberty (KJ) is not. Grand Cherokee models from the ZJ and WJ generations use different axles and are not covered. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

A 4.88 ratio changes the top speed and the low-speed pulling characteristics, so confirm the tire size and transfer case setup before you choose the ratio. Fit the front and rear sets to their own carriers, and check pinion depth and backlash after assembly.

What’s included

Front and rear 4.88 ring and pinion sets, plus matched master installation kits for both axles.

SKU: G/24-XJ4-488 Categories: ,

Specification

Shipping weight 38.72 lbs
Package dimensions 0.00 × 0.00 × 0.00 in
brands

Fitment

VehicleYearsTrims
Jeep Cherokee (XJ) likely fits1984–2001All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the G2 4-XJ4-488 kit fit a 1998 Jeep Cherokee XJ?

Yes. The kit is stated to fit 1984 to 2001 XJ Cherokee models, so a 1998 XJ is inside that range. Confirm the front is a Dana 30 reverse and the rear is a Dana 44 with the carrier sizes listed.

What does a 4.88 ring and pinion ratio mean?

It means the pinion gear turns 4.88 times for each full turn of the ring gear. A higher ratio like this gives more torque at the wheels and lower engine speed at a given road speed.

Are the master installation kits included?

Yes. Matched master installation kits for the front and rear axles are included with the 4.88 ring and pinion sets, so the kit covers both axles in one purchase.

How often should ring and pinion gears be inspected after install?

Check for whine, leaks and vibration during regular oil changes. Look at the tooth contact and bearing fit again after the first few hundred miles, since that is when new parts settle. Address any new noise early, before it damages the gears.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon