Select your vehicle
-13%

G2 XJ Cherokee Front and Rear 4.56 Ring and Pinion Kit – 4-XJ3-456

G2 Axle and Gear

Shop Jeep Cherokee XJ Ring And Pinions on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • 4.56 front and rear ring and pinion kit for the Cherokee XJ
  • Dana 30 short front, Dana 35 rear
  • Front and rear matched master installation kits
  • Part number 4-XJ3-456, 1984–2001

Description

Overview

The G2 Axle and Gear 4-XJ3-456 is a 4.56 front and rear ring and pinion kit for the 1984–2001 Jeep Cherokee (XJ), built with a Dana 30 short front and a Dana 35 rear. It includes the gears and matched master installation kits needed for a gear swap.

Both ends run the same 4.56 ratio. The kit carries a limited lifetime warranty, and the gears are computer heat treated 8620 steel, manufactured to O.E. specs, double shot peened and double lapped.

Key features

  • 4.56 gears front and rear
  • Dana 30 short front, Dana 35 rear
  • Master installation kit for each axle
  • Fits 1984 to 2001 XJ Cherokee
  • Limited lifetime warranty

Before the gear swap

Gear swaps on a Dana 30 and Dana 35 are often done alongside the axle bearings, seals and carrier inspection. Pull the axle, inspect the housing for cracks and the bearing bores for wear, and replace anything loose or rough. Doing this work while the axle is open saves a second teardown later.

The master installation kits help with pinion depth and preload, but the setup still takes care. Shim the carrier to set backlash, then check tooth contact with marking compound. Adjust until the pattern sits centered on the teeth. Fill with fresh gear oil and run the axle gently for the first miles before towing or hard use.

  • Inspect and replace the axle bearings if worn
  • Check the axle housing for cracks and seal surfaces
  • Replace axle seals during the gear change

Specifications

Brand G2 Axle and Gear
Part number 4-XJ3-456
UPC 700007521781
Product type Front and rear ring and pinion sets with master installation kits
Gear ratio 4.56
Front axle gears Dana 30 Short 4.56
Front carrier 3.73 and up
Rear axle gears Dana 35 4.56
Rear carrier 3.54 and up
Installation kits Front and rear matched master installation kits
Material Computer heat treated 8620 steel
Manufacturing Manufactured to O.E. specs, double shot peened, double lapped
Warranty Limited lifetime warranty

Vehicle fitment

The 4-XJ3-456 fits the 1984 to 2001 XJ Cherokee with a Dana 30 short front axle and a Dana 35 rear axle.

The 4-XJ3-456 does not cover an XJ with a reverse-cut Dana 30 front or other Jeep models. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The front gears need a 3.73 and up carrier, and the rear gears need a 3.54 and up carrier. Pinion depth, preload and backlash must be set on both axles, and the master installation kits help with that. Professional setup is the usual route.

What’s included

  • Front ring and pinion gear set
  • Rear ring and pinion gear set
  • Front matched master installation kit
  • Rear matched master installation kit

Not included: carriers and anything beyond the two master installation kits.

SKU: G/24-XJ3-456 Category:

Specification

Shipping weight 32.86 lbs
Package dimensions 0.00 × 0.00 × 0.00 in
brands

Fitment

VehicleYearsTrims
Jeep Cherokee (XJ) likely fits1984–2001All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What years does the G2 4-XJ3-456 fit?

It fits the 1984 to 2001 XJ Cherokee, with a Dana 30 short front axle and a Dana 35 rear axle. Confirm your vehicle's year, model and trim before ordering.

What ratio is the 4-XJ3-456?

It is a 4.56 set for both the front Dana 30 short axle and the rear Dana 35 axle, supplied with matched master installation kits.

What carrier does the 4-XJ3-456 need?

The front gears need a 3.73 and up carrier, and the rear gears need a 3.54 and up carrier. Check both carriers against your setup before ordering, since carriers are not part of this kit.

Should axle bearings be replaced during a gear swap?

Often yes. Bearings and seals cost little compared with the labor of pulling the axle again. Inspect them while the axle is open, and replace any that feel rough, have play or show heat marks before the new gears go in.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Cherokee XJ Ring And Pinions on Amazon