Select your vehicle
-13%

G2 TJ Rubicon Front and Rear 4.88 Ring and Pinion Kit – 4-TJRUB-488

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Front and rear 4.88 ring and pinion kit for Rubicon TJ Wranglers
  • Dana 44 front axle and Dana 44 rear axle
  • Matched front and rear master installation kits
  • Computer heat treated 8620 steel
  • Limited lifetime warranty

Description

Overview

The G2 Axle and Gear 4-TJRUB-488 is a 4.88 ratio front and rear ring and pinion kit for the Rubicon Jeep Wrangler TJ, with Dana 44 axles at both ends. The TJ chassis code covers the 1997-2006 Wrangler. The kit is made for Rubicon models.

Since both ends use Dana 44 axles, the same ratio is set at the front and the rear. The kit includes matched master installation kits for each axle, so the two gear sets go into their own carriers without mixing parts.

Key features

  • Front and rear 4.88 ratio ring and pinion sets
  • Dana 44 front and Dana 44 rear gear sets
  • Matched master installation kits for both axles
  • Computer heat treated 8620 steel gears
  • Built to original equipment specifications

Rubicon TJ gearing choices

Choosing a shorter ratio for a Rubicon TJ is mainly about how the vehicle is used. A steeper ratio helps with low speed crawling and slow technical sections, while a more relaxed ratio suits long highway runs. Consider how the vehicle spends most of its time before committing to a set.

Because the axles are the same design at both ends, the front and rear gears share the same load characteristics. Check the front and rear carriers for wear at the same time, and keep the seals fresh while the housings are open. Good gear oil and regular inspections keep both ends working evenly.

  • Typical use: crawling or highway driving
  • Front and rear carrier wear checks
  • Axle seal condition while the housings are open

Specifications

Brand G2 Axle and Gear
Part number 4-TJRUB-488
UPC 700007521631
Gear ratio 4.88
Front axle Dana 44
Rear axle Dana 44
Material Computer heat treated 8620 steel
Models Rubicon
Warranty Limited lifetime

Vehicle fitment

The TJ chassis code in the name covers the 1997-2006 Wrangler. The kit is made for Rubicon models with Dana 44 axles at both ends.

The TJ years run 1997 to 2006, so YJ, LJ and JK Wranglers are not covered. A non-Rubicon TJ may use a different front axle, so check the axle setup before ordering. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Set pinion depth and backlash on both axles after the gears are installed, and use the master installation kit supplied with each set. Because both axles are Dana 44s, check that each carrier matches its gear set before the swap.

What’s included

Front and rear 4.88 ring and pinion sets, with matched master installation kits for both axles.

SKU: G/24-TJRUB-488 Categories: ,

Specification

Shipping weight 94.40 lbs
Package dimensions 0.00 × 0.00 × 0.00 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (TJ) likely fits1997–2006All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the G2 4-TJRUB-488 kit fit a 2001 Jeep Wrangler Rubicon TJ?

Yes. The TJ chassis code covers the 1997-2006 Wrangler, and this kit is made for Rubicon models, so a 2001 Rubicon TJ is in range. Confirm both axles are Dana 44s before ordering.

Is the front axle on this kit a Dana 44?

Yes. G2 lists Dana 44 axles at both the front and rear for this kit, so the front gears are matched to a Dana 44 carrier, not a Dana 30.

What ratio does the Rubicon TJ 4-TJRUB-488 use?

The ratio is 4.88 for both the front and rear ring and pinion sets. Matched master installation kits for each axle come in the same package.

Should I replace the axle seals during a gear change?

It is a sensible time to do so, since the housings are open for the job. Fresh seals reduce the chance of leaks with the new gears.

Does a Rubicon TJ need extra checks after new gears?

Yes. Check the front and rear carriers and the driveline after the first few drives, since both ends now share the same gearing.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon