Select your vehicle

G2 TJ Front and Rear 4.88 Ring and Pinion Kit – 4-TJ-488

G2 Axle and Gear

Shop Jeep Wrangler TJ Ring And Pinions on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • TJ Wrangler, non-Rubicon
  • 4.88 ring and pinion kit, front and rear
  • Dana 30 front and Dana 35 rear
  • Two matched Master Installation Kits

Description

Overview

The G2 Axle and Gear 4-TJ-488 is a front and rear 4.88 ring and pinion kit designed for non-Rubicon Jeep Wrangler (TJ) models with a Dana 30 front and Dana 35 rear axle. Two matched Master Installation Kits come with the gear sets.

A 4.88 ratio is a tall step from stock gearing and is generally aimed at large tire sizes, where it helps the engine pull the extra rotating mass. Engine speed at highway pace rises as well. G2 says its gears are computer heat treated 8620 steel, double shot peened and double lapped, built to O.E. specifications.

G2 provides a limited lifetime warranty on the kit. It is built for the 1997-2006 Jeep Wrangler (TJ) in non-Rubicon form.

Key features

  • 4.88 ratio at both axles
  • Non-Rubicon Wrangler application
  • Dana 30 front and Dana 35 rear
  • Front and rear Master Installation Kits included
  • Computer heat treated 8620 steel
  • Double shot peened and lapped
  • Limited lifetime warranty from G2

Break-in and checks

A full ring and pinion swap is a break-in event. New gears and bearings settle as they run, so the first miles deserve gentle throttle use and minimal towing or hard acceleration. Listen for changes in noise and check for leaks at the housing covers and seals after the first short drives.

Routine checks keep the swap working. Look at gear oil level and condition at the first service, and check the carrier bolts and cover fasteners for torque after the initial trips. Because the gearing loads the engine differently at speed, keep an eye on engine temperature during long stretches of paved highway driving.

  • Check gear oil level after break-in
  • Re-check cover bolts after early trips
  • Listen for new noise at speed
  • Monitor engine temperature on long highway runs

Specifications

Brand G2 Axle and Gear
Part number 4-TJ-488
UPC 700007521611
Gear ratio 4.88
Front axle Dana 30 TJ
Rear axle Dana 35
Application Non-Rubicon models
Material Computer heat treated 8620 steel
Finishing Double shot peened, double lapped
Warranty Limited lifetime (G2)

G2 does not provide tooth counts, the set weight or the installation kit contents.

Vehicle fitment

G2 has not supplied a vehicle list for the 4-TJ-488, but the title carries the TJ code for the 1997-2006 Jeep Wrangler (TJ). The kit is limited to non-Rubicon models.

The recorded fitment is based on the product title and description, with no trim narrowing.

Not covered: Rubicon Wranglers and non-TJ generations (YJ, JK, JL). Confirm your vehicle’s year, model and trim before ordering.

Installation notes

A full 4.88 swap means setting pinion depth and backlash on two axles, so it is normally done by a shop with the right gauges. Allow time for gentle break-in miles afterward.

Install the front and rear sets together so each installation kit stays matched to its gears.

What’s included

  • Front ring and pinion set, 4.88
  • Rear ring and pinion set, 4.88
  • Front Master Installation Kit
  • Rear Master Installation Kit

Not included: gear oil and related parts.

SKU: G/24-TJ-488 Category:

Specification

Shipping weight 33.86 lbs
Package dimensions 0.00 × 0.00 × 0.00 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (TJ) likely fits1997–2006All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Is the 4-TJ-488 only for a TJ?

Yes, it is for the TJ Wrangler in non-Rubicon models, with a Dana 30 front and Dana 35 rear axle. It is not intended for other Wrangler generations.

What ratio is the G2 4-TJ-488?

It is a 4.88 kit. Both the front and the rear gear sets share that ratio so the two axles remain matched.

What comes in the box with the 4-TJ-488?

Two ring and pinion sets and two matched Master Installation Kits, one front and one rear. G2 does not break down what is in the installation kits.

Does a 4.88 ratio change fuel economy?

Yes, in general. At a set road speed the engine turns faster with this ratio, which can affect fuel use and cruising noise. Results depend on tire size, engine and driving style.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wrangler TJ Ring And Pinions on Amazon